The standard Makefile output is very noisy and it can be difficult to
filter the interesting information from this noise.
In quiet mode the standard Makefile output will be suppressed and instead a
short human readable description of the current task is shown.
E.g.
> make adv7511.zed
Building axi_clkgen library [library/axi_clkgen/axi_clkgen_ip.log] ... OK
Building axi_hdmi_tx library [library/axi_hdmi_tx/axi_hdmi_tx_ip.log] ... OK
Building axi_i2s_adi library [library/axi_i2s_adi/axi_i2s_adi_ip.log] ... OK
Building axi_spdif_tx library [library/axi_spdif_tx/axi_spdif_tx_ip.log] ... OK
Building util_i2c_mixer library [library/util_i2c_mixer/util_i2c_mixer_ip.log] ... OK
Building adv7511_zed project [projects/adv7511/zed/adv7511_zed_vivado.log] ... OK
Quiet mode is enabled by default since it generates a more human readable
output. It can be disabled by passing VERBOSE=1 to make or setting the
VERBOSE environment variable to 1 before calling make.
E.g.
> make adv7511.zed VERBOSE=1
make[1]: Entering directory 'library/axi_clkgen'
rm -rf *.cache *.data *.xpr *.log component.xml *.jou xgui
*.ip_user_files *.srcs *.hw *.sim .Xil .timestamp_altera
vivado -mode batch -source axi_clkgen_ip.tcl >> axi_clkgen_ip.log 2>&1
...
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Some IP core have files in their file list for common modules that are not
used by the IP itself. Remove those.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the IP component dependency in the Makefile system is the Vivado
project file. The project file is only a intermediary product in producing
the IP component definition file.
If building the component definition file fails or the process is aborted
half way through it is possible that the Vivado project file for the IP
component exists, but the IP component definition file does not.
In this case there will be no attempt to build the IP component definition
file when building a project that has a dependency on the IP component.
Building the project will fail in this case.
To avoid this update the Makefile rules so that the IP component definition
file is used as the dependency. In this case the IP component will be
re-build if the component definition file does not exist, even if the
project file exists.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Removes a lot of boilerplate code.
Using the new scheme it is possible to add new projects or sub-projects
without having to re-generate any existing Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The project top-level Makefile accept the all, clean and clean-all targets
and forward them to their sub-projects.
Create a common Makefile include that can be used to implement this
behavior. The shared Makefile collects all sub-directories that have a
Makefile and then forwards the all, clean and clean-all targets to them.
This is implemented by creating virtual targets for each combination of
sub-project and all, clean, clean-all targets in the form of
"$project/all", ... These virtual sub-targets are then listed as the
prerequisites of the project top-level Makefile targets.
This means there is no longer a need to re-generate top-level Makefiles
when a new project or sub-project is added.
It will also allow to remove a lot of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The project Makefiles for the Xilinx projects share most of their code. The
only difference is the list of project dependencies.
Create a file that has the common parts and can be included by the project
Makefiles.
This drastically reduces the size of the project Makefiles and also allows
to change the Makefile implementation without having to re-generate all
Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The project Makefiles for the Altera projects share most of their code. The
only difference is the list of project dependencies.
Create a file that has the common parts and can be included by the project
Makefiles.
This drastically reduces the size of the project Makefiles and also allows
to change the Makefile implementation without having to re-generate all
Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The TX side runs on QPLL, and the RX and RX_OS runs on CPLL by default.
The OUTCLK frequency is the same as the REFCLK.
The main reason of this modification is that the links should come up
without any DPR access, after power up, using the default reference clock
configuration (122.88 MHz).
This way the user do not need to modify the block design, just
set the required rate in system_bd.tcl.
This commit does not contain any functional changes.
Explicitly select MIO 52 and 53 pins to be part of MDIO port.
MIO_52_PIN (MDIO 0 Clock, Output)
MIO_53_PIN (MDIO 0 Data, Input/Output)
After the tool version change, this pins where by default connected
as MIO GPIOs.
Explicitly disable the "Transfer Start Synchronisation Support"
since the sync lines are not connected in this project.
If the sync input line (s_axi_user[0] or fifo_wr_sync) are not connected,
Vivado 2017.4.1 no longer connects them to the defaultValue defined
in the axi_dmac ip (1). Instead he uses the defaulValue field defined
in the interface definition which in case of both interfaces is 0;
Loop back the unused GPIO pins, and add all the SPI interface to system
wrapper instance.
The following system_top modules were changed:
- ad738x_fmc
- ad7616_sdz
- ad77681evb
- ad77681evb
- ad7768evb
- ad9739a_fmc
- ad9434
- adrv9739
- fmcadc5
- ad6676evb
- ad9265
- ad5766
- fmcomms5
- m2k
The constraint where added to remove timing problems on the reset path.
The constraint paths do not match anymore. The resets are used in a synchronous
way so we don't need the timing exceptions anyway.
Projects affected by this change:
- daq3
- adrv9739
- ad6676evb
- fmcadc5
- daq2/kcu105
- fmcadc2
- adrv9371x
- fmcomms11/zc706
- fmcjesdadc1
By default every base design has a SPI interface (hard or soft). In
case of soft IPs (xilinx), the input registers of the interface by default have
the IOB attribute set to TRUE. If the interface are not used, the tool will
generate a critical warning, stating that IOB registers are not connected to
an IO buffer.
The following constraints are disabling the above setup for every base
design, which using a soft SPI IP.
Set the properties to mirror the hardware configuration so
the Vivado tools can provide warnings if there are any conflicts
between configuration pin settings, such as an IOSTANDARD
on a multi-function configuration pin that conflicts with the
configuration voltage.
see:
https://www.xilinx.com/support/documentation/user_guides/ug570-ultrascale-configuration.pdf
The following base constraints were updated:
- kcu105
- kc705
- vc707
- ac701
To reduce compilation time use default stratagies for synthesis and
implementation. If a project will require custom strategies, enable it
just for that particular project.
This modification will affect both Intel and Xilinx projects.
Vivado sometimes generates semi-valid or invalid warnings and critical warnings.
In the past these messages were silenced, by changing its message severity.
These setups were scattered in multiple scripts. This commit is an attempt
to centralize it and make it more maintainable and easier to review it.
The script specifies the OUT_CLK_SEL and SYS_CLK_SEL parameter values as
binary numbers. But the tools will interpret them as decimal number
resulting in the wrong selection for OUT_CLK_SEL. Specify the parameter
values as decimal values to avoid this.
This is not a critical issue since software will overwrite this setting at
system boot-up. But it should be fixed anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The script specifies the OUT_CLK_SEL and SYS_CLK_SEL parameter values as
binary numbers. But the tools will interpret them as decimal number
resulting in the wrong selection for OUT_CLK_SEL. Specify the parameter
values as decimal values to avoid this.
This is not a critical issue since software will overwrite this setting at
system boot-up. But it should be fixed anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes the following warning:
[Synth 8-2611] redeclaration of ansi port rx_sysref is not allowed
This is a leftover of commit 1c23cf4621 ("all: Update verilog files to
verilog-2001").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes the following warnings:
[Synth 8-2611] redeclaration of ansi port txnrx_0 is not allowed
[Synth 8-2611] redeclaration of ansi port enable_0 is not allowed
[Synth 8-2611] redeclaration of ansi port enable_1 is not allowed
[Synth 8-2611] redeclaration of ansi port txnrx_1 is not allowed
This is a leftover of commit 1c23cf4621 ("all: Update verilog files to
verilog-2001").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that the axi_adxcvr instances are configured with the same
transceiver type as the util_adxcvr.
This is necessary for software to be able to detect the transceiver type
and support dynamic reconfiguration.
It is also necessary for correct eye scan support in the axi_adxcvr block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that the axi_adxcvr instances are configured with the same
transceiver type as the util_adxcvr.
This is necessary for software to be able to detect the transceiver type
and support dynamic reconfiguration.
It is also necessary for correct eye scan support in the axi_adxcvr block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the location assignment of the transceiver blocks to get the correct
lane mapping.
Note that the comments indicating the expected lane mapping are correct,
but the actual transceiver location assignments were not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The external reference clock runs at 122.88 MHz by default. This means that
the QPLL feedback divider needs to be set to 80 so that the VCO is inside
the locking range (9.8 GHz - 16.375 GHz).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
DAC data underflow from the DMA, was not connected to anything. This
signal should be connected to the util_rfifo, which will forward it to
the device core.
+ Build both the read and write logic around an FSM
+ Consistent naming of registers and wires
+ Add support for burst lenghts higher than one, current burst lenght
is 64
+ Fix all the bugs, and make it work (first bring up with
adrv9371x/a10soc)
If the ADI_HDL_DIR or ADI_PHDL_DIR are set on Windows platforms, an
invalid TCL character (e.g. backslash) may be used as a file separator,
causing issues with the build / library scripts.
Normalize the paths before using them as global TCL variables.
Lars-Peter Clausen
Istvan Csomortani
AndreiGrozav
Rejeesh Kutty
Adrian Costina
Laszlo Nagy
Michael Hennerich
Matt Fornero
STEVE KRAVATSKY