For consistent simulation behavior it is recommended to annotate all source
files with a timescale. Add it to those where it is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
If the req_valid asserts faster than the ID gets synchronized over we
assert the xfer request without being ready to accept data.
This can lead to overflow assertion when using a FIFO like interface.
Data mover/ src axis changes
Request rewind ID if TLAST received during non-last burst
Consume (ignore) descriptors until last segment received
Block descriptors towards destination until last segment received
Request generator changes
Rewind the burst ID if rewind request received
Consume (ignore) descriptors until last segment received
If TLAST happened on last segment replay next transfer (in progress or
completed) with the adjusted ID
Create completion requests for ignored segments
Response generator changes
Track requests
Complete segments which got ignored
Length of partial transfers are stored in a queue for SW reads.
The presence of partial transfer is indicated by a status bit.
The reporting can be enabled by a control bit.
The progress of any transfer can be followed by a debug register.
Drive the descriptor from the source side to destination
so we can abort consecutive transfers in case TLAST asserts.
For AXIS count the length of the burst and pass that value to the
destination instead the programmed one. This is useful when the
streams aborts early by asserting the TLAST. We want to notify the
destination with the right number of beats received.
For FIFO source interface reuse the same logic due the small footprint
even if the stream does not got interrupted in that case.
For MM source interface wire the burst length from the request side to
destination.
Vivado recognises .h files as C header files,
the expected extension for Verilog Header is .vh
This causes issues in simulating block designs since these files
won't be exported for the simulation even if they are
part of the simulation fileset.
The transfer abort logic in the src_axi_stream module is making some
assumptions about the internal timings of the data mover module.
Move this logic inside the data mover module. This will make it easier to
update the internal logic without having to update other modules.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The only two users of the data mover module both implement the same
sync-transfer-start logic. Move this into the data mover module to avoid
the duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
With the recent rework there is now a fair amount of dead code in the
datamover module that is no longer used. Remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMAC allows a transfer to be aborted. When a transfer is aborted the
DMAC shuts down as fast as possible while still completing any pending
transactions as required by the protocol specifications of the port. E.g.
for AXI-MM this means to complete all outstanding bursts.
Once the DMAC has entered an idle state a special synchronization signal is
send to all modules. This synchronization signal instructs them to flush
the pipeline and remove any stale data and metadata associated with the
aborted transfer. Once all data has been flushed the DMAC enters the
shutdown state and is ready for the next transfer.
In addition each module has a reset that resets the modules state and is
used at system startup to bring them into a consistent state.
Re-work the shutdown process to instead of flushing the pipeline re-use the
startup reset signal also for shutdown.
To manage the reset signal generation introduce the reset manager module.
It contains a state machine that will assert the reset signals in the
correct order and for the appropriate duration in case of a transfer
shutdown.
The reset signal is asserted in all domains until it has been asserted for
at least 4 clock cycles in the slowest domain. This ensures that the reset
signal is not de-asserted in the faster domains before the slower domains
have had a chance to process the reset signal.
In addition the reset signal is de-asserted in the opposite direction of
the data flow. This ensures that the data sink is ready to receive data
before the data source can start sending data. This simplifies the internal
handshaking.
This approach has multiple advantages.
* Issuing a reset and removing all state takes less time than
explicitly flushing one sample per clock cycle at a time.
* It simplifies the logic in the faster clock domains at the expense of
more complicated logic in the slower control clock domain. This allows
for higher fMax on the data paths.
* Less signals to synchronize from the control domain to the data domains
The implementation of the pause mode has also slightly changed. Pause is
now a simple disable of the data domains. When the transfer is resumed
after a pause the data domains are re-enabled and continue at their
previous state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that the right hand side expression of assignments is not wider
than the target signal. This avoids warnings about implicit truncations.
None of these changes affect the behaviour, just fixes some warnings about
implicit signal truncation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
For the AXI stream interface we want to generate TLAST only at the end of
the transfer, rather than at the end of each burst.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
We do not know which 'last' condition to use before hand, but we can pre-compute
the result for both conditions and then use them. This removes the comparison
from the already pretty long combinatorial path.
Also simplify a few expressions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The pending_burst signal and the expression id != request_id are almost
identical. pending_burst goes high with a delay of one clock cycle, but the
important thing is that it goes low on the same clock cycle as the expression.
By using pending_burst here instead of 'id != request_id' we can reduce the
fanout of the 'id' register and improve the timing of the core.
There were a few place in the core where it assumed a 64-bit wide bus. Make this
configurable using parameters. The patch also adds support for having different
DMA bus widths on the source and destination side.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Right now there is always a period of one clock cycle where we can not transfer
any data when switching between two transfers. This patch modifies the data
mover to allow for zero latency. This fixes problems on the FMCOMMS1 platform
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Lars-Peter Clausen
Laszlo Nagy
Istvan Csomortani
Adrian Costina