// *************************************************************************** // *************************************************************************** // Copyright 2018 (c) Analog Devices, Inc. All rights reserved. // // In this HDL repository, there are many different and unique modules, consisting // of various HDL (Verilog or VHDL) components. The individual modules are // developed independently, and may be accompanied by separate and unique license // terms. // // The user should read each of these license terms, and understand the // freedoms and responsibilities that he or she has by using this source/core. // // This core is distributed in the hope that it will be useful, but WITHOUT ANY // WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR // A PARTICULAR PURPOSE. // // Redistribution and use of source or resulting binaries, with or without modification // of this file, are permitted under one of the following two license terms: // // 1. The GNU General Public License version 2 as published by the // Free Software Foundation, which can be found in the top level directory // of this repository (LICENSE_GPL2), and also online at: // // // OR // // 2. An ADI specific BSD license, which can be found in the top level directory // of this repository (LICENSE_ADIBSD), and also on-line at: // https://github.com/analogdevicesinc/hdl/blob/master/LICENSE_ADIBSD // This will allow to generate bit files and not release the source code, // as long as it attaches to an ADI device. // // *************************************************************************** // *************************************************************************** `timescale 1ns / 1ps module data_offload #( parameter ID = 0, parameter [ 0:0] MEM_TYPE = 1'b0, // 1'b0 -FPGA RAM; 1'b1 - external memory parameter [33:0] MEM_SIZE = 1024, // memory size in bytes -1 - max 16 GB parameter MEMC_UIF_DATA_WIDTH = 512, parameter MEMC_UIF_ADDRESS_WIDTH = 31, parameter [31:0] MEMC_BADDRESS = 32'h00000000, parameter TX_OR_RXN_PATH = 0, // if set IP is used in TX path, other wise in RX path parameter SRC_DATA_WIDTH = 64, parameter SRC_RAW_DATA_EN = 1'b0, parameter SRC_ADDR_WIDTH = 8, parameter DST_ADDR_WIDTH = 7, parameter DST_DATA_WIDTH = 128, parameter DST_RAW_DATA_EN = 1'b0, // TBD parameter DST_CYCLIC_EN = 1'b0, // 1'b1 - CYCLIC mode enabled; 1'b0 - CYCLIC mode disabled parameter AUTO_BRINGUP = 1, parameter SYNC_EXT_ADD_INTERNAL_CDC = 1) ( // AXI4 Slave for configuration input s_axi_aclk, input s_axi_aresetn, input s_axi_awvalid, input [15:0] s_axi_awaddr, input [ 2:0] s_axi_awprot, output s_axi_awready, input s_axi_wvalid, input [31:0] s_axi_wdata, input [ 3:0] s_axi_wstrb, output s_axi_wready, output s_axi_bvalid, output [ 1:0] s_axi_bresp, input s_axi_bready, input s_axi_arvalid, input [15:0] s_axi_araddr, input [ 2:0] s_axi_arprot, output s_axi_arready, output s_axi_rvalid, input s_axi_rready, output [ 1:0] s_axi_rresp, output [31:0] s_axi_rdata, // AXI4 stream slave for source stream (TX_DMA or ADC) -- Source interface input s_axis_aclk, input s_axis_aresetn, output s_axis_ready, input s_axis_valid, input [SRC_DATA_WIDTH-1:0] s_axis_data, input s_axis_last, input [SRC_DATA_WIDTH/8-1:0] s_axis_tkeep, // AXI4 stream master for destination stream (RX_DMA or DAC) -- Destination // interface input m_axis_aclk, input m_axis_aresetn, input m_axis_ready, output m_axis_valid, output [DST_DATA_WIDTH-1:0] m_axis_data, output m_axis_last, output [DST_DATA_WIDTH/8-1:0] m_axis_tkeep, // initialization request interface input init_req, output init_ack, input sync_ext, // FIFO interface - Memory UI output fifo_src_wen, output fifo_src_resetn, output [SRC_ADDR_WIDTH-1:0] fifo_src_waddr, output [SRC_DATA_WIDTH-1:0] fifo_src_wdata, output fifo_src_wlast, output fifo_dst_ren, input fifo_dst_ready, output fifo_dst_resetn, output [DST_ADDR_WIDTH-1:0] fifo_dst_raddr, input [DST_DATA_WIDTH-1:0] fifo_dst_rdata, // Status and monitor input ddr_calib_done ); // local parameters -- to make the code more readable localparam SRC_ADDR_WIDTH_BYPASS = (SRC_DATA_WIDTH > DST_DATA_WIDTH) ? 3 : 3 + $clog2(SRC_DATA_WIDTH/DST_DATA_WIDTH); localparam DST_ADDR_WIDTH_BYPASS = (SRC_DATA_WIDTH <= DST_DATA_WIDTH) ? 3 + $clog2(DST_DATA_WIDTH/SRC_DATA_WIDTH) : 3; localparam SRC_BEAT_BYTE = $clog2(SRC_DATA_WIDTH/8); // NOTE: Clock domain prefixes // src_* - AXI4 Stream Slave interface's clock domain // dst_* - AXI4 Stream Master interface's clock domain // internal signals wire up_clk; wire up_rstn; wire up_wreq_s; wire [13:0] up_waddr_s; wire [31:0] up_wdata_s; wire up_rreq_s; wire [13:0] up_raddr_s; wire up_wack_s; wire up_rack_s; wire [31:0] up_rdata_s; wire src_clk; wire src_rstn; wire src_valid_out_s; wire [SRC_ADDR_WIDTH-1:0] src_wr_addr_s; wire src_wr_ready_s; wire src_wr_last_s; wire [SRC_DATA_WIDTH/8-1:0] src_wr_tkeep_s; wire dst_clk; wire dst_rstn; wire [DST_ADDR_WIDTH-1:0] dst_raddr_s; wire [DST_DATA_WIDTH-1:0] dst_mem_data_s; wire src_bypass_s; wire dst_bypass_s; wire oneshot_s; wire [63:0] sample_count_s; wire [ 1:0] sync_config_s; wire sync_int_s; wire valid_bypass_s; wire [DST_DATA_WIDTH-1:0] data_bypass_s; wire ready_bypass_s; wire [ 1:0] src_fsm_status_s; wire [ 1:0] dst_fsm_status_s; wire m_axis_valid_s; wire m_axis_last_s; wire [DST_DATA_WIDTH-1:0] m_axis_data_s; wire dst_mem_valid_s; wire dst_mem_valid_int_s; wire m_axis_reset_int_s; wire [33:0] src_transfer_length_s; wire src_wr_last_int_s; wire [33:0] src_wr_last_beat_s; wire int_not_full; assign src_clk = s_axis_aclk; assign dst_clk = m_axis_aclk; // internal registers reg [33:0] src_data_counter = 0; reg dst_mem_valid_d = 1'b0; generate if (TX_OR_RXN_PATH) begin assign src_wr_last_s = s_axis_last; assign src_wr_tkeep_s = s_axis_tkeep; assign m_axis_reset_int_s = ~dst_rstn; end else begin assign src_wr_last_s = src_wr_last_int_s; assign src_wr_tkeep_s = {(SRC_DATA_WIDTH/8){1'b1}}; assign m_axis_reset_int_s = ~dst_rstn | ~init_req; end endgenerate assign fifo_src_wlast = src_wr_last_s; // Offload FSM and control data_offload_fsm #( .TX_OR_RXN_PATH (TX_OR_RXN_PATH), .WR_ADDRESS_WIDTH (SRC_ADDR_WIDTH), .WR_DATA_WIDTH (SRC_DATA_WIDTH), .RD_ADDRESS_WIDTH (DST_ADDR_WIDTH), .RD_DATA_WIDTH (DST_DATA_WIDTH), .SYNC_EXT_ADD_INTERNAL_CDC (SYNC_EXT_ADD_INTERNAL_CDC )) i_data_offload_fsm ( .up_clk (up_clk), .wr_clk (src_clk), .wr_resetn_in (src_rstn), .wr_resetn_out (fifo_src_resetn), .wr_valid_in (s_axis_valid), .wr_valid_out (fifo_src_wen), .wr_ready (src_wr_ready_s), .wr_addr (fifo_src_waddr), .wr_last (src_wr_last_s), .wr_tkeep (src_wr_tkeep_s), .rd_clk (dst_clk), .rd_resetn_in (dst_rstn), .rd_resetn_out (fifo_dst_resetn), .rd_ready (fifo_dst_ready_int_s), .rd_valid (dst_mem_valid_s), .rd_addr (fifo_dst_raddr), .rd_last (), .rd_tkeep (m_axis_tkeep), .rd_oneshot (oneshot_s), .init_req (init_req), .init_ack (init_ack), .sync_config (sync_config_s), .sync_external (sync_ext), .sync_internal (sync_int_s), .wr_fsm_state (src_fsm_status_s), .rd_fsm_state (dst_fsm_status_s), .sample_count (sample_count_s) ); // In case of external memory, read back can not start right after the write // was finished (because of the CDC FIFOs and the latency of the EMIF // interface) generate if (MEM_TYPE == 1'b1) begin assign dst_mem_valid_int_s = dst_mem_valid_s; end else begin // Compensate the 1 cycle READ latency of the BRAM always @(posedge m_axis_aclk) begin dst_mem_valid_d <= dst_mem_valid_s; end assign dst_mem_valid_int_s = dst_mem_valid_d; end endgenerate assign fifo_dst_ready_int_s = fifo_dst_ready & int_not_full; assign fifo_src_wdata = s_axis_data; assign fifo_dst_ren = dst_mem_valid_s; ad_axis_inf_rx #( .DATA_WIDTH (DST_DATA_WIDTH)) i_rx_axis_inf ( .clk (m_axis_aclk), .rst (m_axis_reset_int_s), .valid (dst_mem_valid_int_s), .data (fifo_dst_rdata), .last (1'b0), .inf_valid (m_axis_valid_s), .inf_last (m_axis_last_s), .inf_data (m_axis_data_s), .inf_ready (m_axis_ready), .int_not_full(int_not_full)); assign m_axis_valid = (dst_bypass_s) ? valid_bypass_s : m_axis_valid_s; assign m_axis_data = (dst_bypass_s) ? data_bypass_s : m_axis_data_s; assign m_axis_last = (dst_bypass_s) ? 1'b0 : m_axis_last_s; assign s_axis_ready = (src_bypass_s) ? ready_bypass_s : src_wr_ready_s; // Bypass module instance -- the same FIFO, just a smaller depth // NOTE: Generating an overflow is making sense just in BYPASS mode, and // it's supported just with the FIFO interface util_axis_fifo_asym #( .S_DATA_WIDTH (SRC_DATA_WIDTH), .S_ADDRESS_WIDTH (SRC_ADDR_WIDTH_BYPASS), .M_DATA_WIDTH (DST_DATA_WIDTH), .ASYNC_CLK (1)) i_bypass_fifo ( .m_axis_aclk (m_axis_aclk), .m_axis_aresetn (dst_rstn), .m_axis_ready (m_axis_ready), .m_axis_valid (valid_bypass_s), .m_axis_data (data_bypass_s), .m_axis_tlast (), .m_axis_empty (), .m_axis_almost_empty (), .s_axis_aclk (s_axis_aclk), .s_axis_aresetn (src_rstn), .s_axis_ready (ready_bypass_s), .s_axis_valid (s_axis_valid), .s_axis_data (s_axis_data), .s_axis_tlast (), .s_axis_full (), .s_axis_almost_full () ); // register map data_offload_regmap #( .ID (ID), .MEM_TYPE (MEM_TYPE), .MEM_SIZE (MEM_SIZE), .TX_OR_RXN_PATH (TX_OR_RXN_PATH), .AUTO_BRINGUP (AUTO_BRINGUP)) i_regmap ( .up_clk (up_clk), .up_rstn (up_rstn), .up_rreq (up_rreq_s), .up_rack (up_rack_s), .up_raddr (up_raddr_s), .up_rdata (up_rdata_s), .up_wreq (up_wreq_s), .up_wack (up_wack_s), .up_waddr (up_waddr_s), .up_wdata (up_wdata_s), .src_clk (s_axis_aclk), .dst_clk (m_axis_aclk), .src_sw_resetn (src_rstn), .dst_sw_resetn (dst_rstn), .ddr_calib_done (ddr_calib_done), .src_bypass (src_bypass_s), .dst_bypass (dst_bypass_s), .oneshot (oneshot_s), .sync (sync_int_s), .sync_config (sync_config_s), .src_transfer_length (src_transfer_length_s), .src_fsm_status (src_fsm_status_s), .dst_fsm_status (dst_fsm_status_s), .sample_count_msb (sample_count_s[63:32]), .sample_count_lsb (sample_count_s[31: 0]) ); // axi interface wrapper assign up_clk = s_axi_aclk; assign up_rstn = s_axi_aresetn; up_axi #( .AXI_ADDRESS_WIDTH (16)) i_up_axi ( .up_rstn (up_rstn), .up_clk (up_clk), .up_axi_awvalid (s_axi_awvalid), .up_axi_awaddr (s_axi_awaddr), .up_axi_awready (s_axi_awready), .up_axi_wvalid (s_axi_wvalid), .up_axi_wdata (s_axi_wdata), .up_axi_wstrb (s_axi_wstrb), .up_axi_wready (s_axi_wready), .up_axi_bvalid (s_axi_bvalid), .up_axi_bresp (s_axi_bresp), .up_axi_bready (s_axi_bready), .up_axi_arvalid (s_axi_arvalid), .up_axi_araddr (s_axi_araddr), .up_axi_arready (s_axi_arready), .up_axi_rvalid (s_axi_rvalid), .up_axi_rresp (s_axi_rresp), .up_axi_rdata (s_axi_rdata), .up_axi_rready (s_axi_rready), .up_wreq (up_wreq_s), .up_waddr (up_waddr_s), .up_wdata (up_wdata_s), .up_wack (up_wack_s), .up_rreq (up_rreq_s), .up_raddr (up_raddr_s), .up_rdata (up_rdata_s), .up_rack (up_rack_s)); /* Beat counter on the source interface * * The storage unit can have size of a couple of Gbyte, which in case of an RX * path would mean to fill up all that memory space before pushing over the * stream to the RX DMA. (ADC can not generate a tlast) To make things more * practical, user can set an arbitrary transfer length using the * transfer_length register, which will be used to generate an internal tlast * signal for the source FSM. If the register is set to zero, all the memory * will be filled up, before passing control to the destination FSM. * */ always @(posedge s_axis_aclk) begin if (fifo_src_resetn == 1'b0) begin // counter should reset when source FMS resets src_data_counter <= 0; end else begin if (fifo_src_wen & src_wr_ready_s) begin src_data_counter <= src_data_counter + 1'b1; end end end // transfer length is in bytes, but counter monitors the source data beats assign src_wr_last_beat_s = (src_transfer_length_s == 'h0) ? MEM_SIZE[33:SRC_BEAT_BYTE]-1 : src_transfer_length_s[33:SRC_BEAT_BYTE]-1; assign src_wr_last_int_s = (src_data_counter == src_wr_last_beat_s) ? 1'b1 : 1'b0; endmodule