.. _build_hdl: Build an HDL project =============================================================================== **Please note that ADI only provides the source files necessary to create and build the designs. This means that you are responsible for modifying and building these projects.** Here, we are giving you a quick rundown on how we build things. That said, the steps below are **not a recommendation**, but a suggestion. How you want to build these projects is entirely up to you. The only catch is that if you run into problems, you have to resolve them independently. The build process depends on certain software and tools, which you could use in many ways. We use **command line** and mostly **Linux systems**. On Windows, we use **Cygwin**. Setup and check your environment ------------------------------------------------------------------------------- This section contains a guide about how to setup your environment to build any HDL project from the repository: #. Install the required FPGA design suite. We use `AMD Xilinx Vivado`_ and `Intel Quartus Prime Pro and Standard`_. You can find information about the proper version in our `release notes `__. Make sure that you're always using the latest release. #. The proper Vivado/Quartus version can be found in: - Starting with ``hdl_2021_r1`` release branch: :git-hdl:`scripts/adi_env.tcl` - For ``hdl_2019_r2`` and older: :git-hdl:`hdl/projects/scripts/adi_project_xilinx.tcl ` for Vivado, and :git-hdl:`hdl/projects/scripts/adi_project_intel.tcl ` for Quartus. #. Download the tools from the following links: - `AMD tools `__ (make sure you're downloading the proper installer. For full installation, it is better to choose the one that downloads and installs both Vivado and Vitis at the same time) - `Intel tools `__ #. After you have installed the above-mentioned tools, you will need the paths to those directories in the following steps, so have them in a note. #. We are using `git `__ for version control and `GNU Make `__ to build the projects. Depending on what OS you're using, you have these options: .. collapsible:: For Windows environment with Cygwin Because GNU Make is not supported on Windows, you need to install `Cygwin `__, which is a UNIX-like environment and command-line interface for Microsoft Windows. You do not need to install any special package, other than ``git`` and ``make``. After you have installed Cygwin, you need to add your FPGA Design Tools installation directory to your PATH environment variable. You can do that by modifying your **.bashrc** file, by adding the following lines (**changed accordingly to your installation directories**). For example: .. code-block:: bash :linenos: export PATH=$PATH:/cygdrive/path_to/Xilinx/Vivado/202x.x/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vivado_HLS/202x.x/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/gnu/microblaze/nt/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/gnu/arm/nt/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/gnu/microblaze/linux_toolchain/nt64_be/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/gnu/microblaze/linux_toolchain/nt64_le/bin export PATH=$PATH:/cygdrive/path_to/Xilinx/Vitis/202x.x/gnu/aarch32/nt/gcc-arm-none-eabi/bin export PATH=$PATH:/cygdrive/path_to/intelFPGA_pro/2x.x/quartus/bin Replace the **path_to** string with your path to the installation folder and the **tools version** with the proper one. .. collapsible:: How to verify your environment setup Run any of the following commands. These commands will return a valid path if your setup is good. .. code-block:: bash [~] which git [~] which make [~] which vivado [~] which quartus Setup the HDL repository ------------------------------------------------------------------------------- These designs are built upon ADI's generic HDL reference designs framework. ADI does not distribute the bit/elf files of these projects so they must be built from the sources available :git-hdl:`here `. To get the source you must `clone `__ the repository. This is the best method to get the sources. Here, we are cloning the repository inside a directory called **adi**. Please refer to the :ref:`git_repository` section for more details. .. code-block:: bash [~] mkdir adi [~] cd adi [~] git clone git@github.com:analogdevicesinc/hdl.git .. warning:: Cloning the HDL repository is done now using SSH, because of GitHub security reasons. Check out this documentation on `how to deal with SSH keys in GitHub `__. Both for `Cygwin `__ and `WSL `__ it is necessary to create a unique SSH key. If you use WSL,to get the best performance, you must clone your hdl repository in the WSL file system. For example: (:code:`\\\\wsl.localhost\\Ubuntu\\home\\username\\hdl`) The above command clones the **default** branch, which is the **main** for HDL. The **main** branch always points to the latest stable release branch, but it also has features **that are not fully tested**. If you want to switch to any other branch you need to checkout that branch: .. code-block:: bash [~] cd hdl/ [~] git status [~] git checkout hdl_2021_r2 If this is your first time cloning, you have all the latest source files. If not, you can simply pull the latest sources using ``git pull`` or ``git rebase`` if you have local changes. .. code-block:: bash [~] git fetch origin # this shows you what changes will be pulled on your local copy [~] git rebase origin/hdl_2021_r2 # this updates your local copy Building the projects ------------------------------------------------------------------------------- .. caution:: Before building any project, you must have the environment prepared and the proper tools. See `Tools`_ section on what you need to download and `Environment`_ section on how to set-up your environment. Building an Intel project ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ An Intel project build is relatively easy. There is no need to build any library components. Go to the directory of the project of interest, then inside the desired carrier run ``make`` to build the project. In this example, I am only interested in the **ADRV9371X** project on the **A10SOC** carrier. .. code-block:: bash cd projects/adrv9371x/a10soc make This assumes that you have the tools and licenses setup correctly. If you don't get to the last line, the make failed to build the project. There is nothing you can gather from the ``make`` output (other than the build failed or not), the actual failure is in a log file. So, let's see how to analyze the build log files and results. .. note:: If you want to use a NIOS-II based project with no-OS software, you have to turn off the MMU feature of the NIOS_II processor. In that case, the make will get an additional attribute: ``make NIOS2_MMU=0`` Checking the build and analyzing results ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ If you look closely at the **rule** for this target, you see it is just calling ``quartus_sh`` with the project TCL file and redirecting the output to a log file. In this case it is called **adrv9371_a10soc_quartus.log** and is inside the **projects/adrv9371x/a10soc** directory. Do a quick (or detailed) check on files. If you are seeking support from us, this contains the most relevant information that you need to provide. .. warning:: Do NOT copy-paste ``make`` command line text .. code-block:: bash ls -ltr projects/adrv9371x/a10soc tail projects/adrv9371x/a10soc/adrv9371x_a10soc_quartus.log And finally, if the project was built is successfully, the **.sopcinfo** and **.sof** files should be in the same folder. .. code-block:: bash ls -ltr projects/adrv9371x/a10soc/*.sopcinfo ls -ltr projects/adrv9371x/a10soc/*.sof You may now use this **sopcinfo** file as the input to your no-OS and/or Linux build. The **sof** file is used to program the device. .. collapsible:: Building an Intel project in WSL - known issues For a10Soc and s10Soc projects it's very possible to face the following error when you try to build the project: .. warning:: Current module quartus_fit was unexpectedly terminated by signal 9. This may be because some system resource has been exhausted, or quartus_fit performed an illegal operation. It can also happen that ``make`` gets stuck when synthesizing some IPs. These errors may appear because your device does not have enough RAM memory to build your FPGA design. This problem can be solved if you create a Linux Swap file. You can find more information about what a swap file is at this link: `SwapFile `__. Depending on the size of the project, more or less virtual memory must be allocated. If you type in the search bar **System Information**, you can see Total Physical Memory and Total Virtual Memory of your system. For example, for the AD9213 with S10SoC project, it was necessary to allocate 15 GB of virtual memory, to be able to make a build for the project. To create a swap file you can use the following commands: .. code-block:: bash :~$ sudo fallocate -l "memory size (e.g 1G, 2G, 8G, etc.)" /swapfile :~$ sudo chmod 600 /swapfile :~$ sudo mkswap /swapfile :~$ sudo swapon /swapfile If you want to make the change permanent: .. code-block:: bash # in /etc/fstab file type the command: /swapfile swap swap defaults 0 0 If you want to deactivate the swap memory: .. code-block:: bash :~$ sudo swapoff -v /swapfile .. collapsible:: Building manually in Quartus GUI .. warning:: We do not recommend using this flow, in general people are losing a lot of valuable time and nerve during this process. There is no need to build any library for Quartus. However, you do need to specify the IP search path for QSYS. This is a global property, so only need to do it once. If you have multiple paths simply add to it. You get to this menu from the **Tools->Options**. The tool then parses these directories and picks up a **\_hw.tcl** file (e.g. **axi_ad9250_hw.tcl**). The peripherals should show up on QSYS library. You may now run the project (generate the sof and software hand-off files) on Quartus. Open the GUI and select TCL console. At the prompt change the directory to where the project is, and source the **system_project.tcl** file. .. code-block:: bash cd c:/github/hdl/projects/daq2/a10soc source ./system_project.tcl You will see commands being executed, the script uses a board design in QSYS, generate all the IP targets, synthesize the netlist and implementation. Building an AMD project ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ An AMD project is built the same way as an Intel project. The only exception is that there are a few 'sub-make(s)' for the library components. The way of building a project in Cygwin and WSL is almost the same. In this example, it is building the **DAQ2** project on the **ZC706** carrier. .. code-block:: bash cd projects/daq2/zc706 make The ``make`` builds all the libraries first and then builds the project. This assumes that you have the tools and licenses setup correctly. If you don't get to the last line, the make failed to build one or more targets: it could be a library component or the project itself. There is nothing you can gather from the ``make`` output (other than which one failed). The actual information about the failure is in a log file inside the project directory. On projects which support this, some ``make`` parameters can be added, to configure the project (you can check the **system_project.tcl** file to see if your project supports this). If parameters were used, the result of the build will be in a folder named by the configuration used. Here are some examples: **Example 1** Running the command below will create a folder named **RXRATE2_5_TXRATE2_5_RXL8_RXM4_RXS1_RXNP16_TXL8_TXM4_TXS1_TXNP16** because of truncation of some keywords so the name will not exceed the limits of the Operating System (**JESD**, **LANE**, etc. are removed) of 260 characters. .. code-block:: bash make RX_LANE_RATE=2.5 TX_LANE_RATE=2.5 RX_JESD_L=8 RX_JESD_M=4 RX_JESD_S=1 RX_JESD_NP=16 TX_JESD_L=8 TX_JESD_M=4 TX_JESD_S=1 TX_JESD_NP=16 **Example 2** Running the command below will create a folder named **LVDSCMOSN1**. .. code-block:: bash make LVDS_CMOS_N=1 Enabling Out-of-Context synthesis ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ You can opt in for out-of-context synthesis during the build by defining the ``ADI_USE_OOC_SYNTHESIS`` system variable. By setting the ``ADI_MAX_OOC_JOBS`` system variable you can adjust the number of maximum parallel out-of-context synthesis jobs. If not set, the default parallel job number is set to 4. .. code-block:: bash export ADI_USE_OOC_SYNTHESIS=y export ADI_MAX_OOC_JOBS=8 cd projects/daq2/zc706 make This will synthesize each IP from the block design individually and will store it in a common cache for future re-use. The cache is located in the **ipcache** folder and is common for all the projects, this way speeding up re-compile of the same project or compile time of common blocks used in base designs. Example: a MicroBlaze base design for VCU118 once compiled, it will be reused on other projects. Using the IP cache will speed up the re-compiles of every project in OOC mode since the cache is not cleared as with normal compile flow. .. caution:: Starting with Vivado 2020.2, Out-of-Context is the default mode. There is no need to set ADI_USE_OOC_SYNTHESIS variable. Set: .. code-block:: bash export ADI_USE_OOC_SYNTHESIS=n only in case you want to use Project Mode. Checking the build and analyzing results of library components ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ If you look closely, you see what it is actually doing. It enters a library component folder then calls **Vivado** in batch mode. The IP commands are in the source Tcl file and output is redirected to a log file. In the below example that is **axi_ad7768_ip.log** inside the **library/axi_ad7768** directory. .. code-block:: bash make[1]: Entering directory '/home/RKutty/gitadi/hdl/library/axi_ad7768' rm -rf *.cache *.data *.xpr *.log component.xml *.jou xgui *.ip_user_files *.srcs *.hw *.sim .Xil vivado -mode batch -source axi_ad7768_ip.tcl >> axi_ad7768_ip.log 2>&1 If the ``make`` command returns an error (and stops), **you must first check the contents of the log file**. You may also check the generated files for more information. .. code-block:: bash ls -ltr library/axi_ad7768 tail library/axi_ad7768/axi_ad7768_ip.log Checking the build and analyzing results of projects ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The last thing that ``make`` does in this above example is building the project. It is exactly the same **rule** as the library component. The log file, in this example, is called **daq2_zc706_vivado.log** and is inside the **projects/daq2/zc706** directory. .. code-block:: bash rm -rf *.cache *.data *.xpr *.log *.jou xgui *.runs *.srcs *.sdk *.hw *.sim .Xil *.ip_user_files vivado -mode batch -source system_project.tcl >> daq2_zc706_vivado.log 2>&1 make: Leaving directory '/home/RKutty/gitadi/hdl/projects/daq2/zc706' Do a quick (or detailed) check on files. .. warning:: Do NOT copy-paste ``make`` command line text .. code-block:: bash ls -ltr projects/daq2/zc706 tail projects/daq2/zc706/daq2_zc706_vivado.log And finally, if the project build is successful, the **.xsa** file should be in the **.sdk** folder. .. code-block:: bash ls -ltr projects/daq2/zc706/daq2_zc706.sdk You may now use this **.xsa** file as the input to your no-OS and/or Linux build. Starting with Vivado 2019.3, the output file extension was changed from **.hdf** to **.xsa**. .. collapsible:: Building an AMD project in WSL - known issues For some projects it is very possible to face the following error when you make a build: .. warning:: ``$RDI_PROG" "$@" crash" "Killed "$RDI_PROG" "$@"`` This error may appear because your device does not have enough RAM memory to build your FPGA design. For example, the project AD-FMCDAQ3-EBZ with Virtex UltraScale+ VCU118 (XCVU9P device) requires 20GB (typical memory) and a peak of 32GB RAM memory. The following link shows the typical and peak Vivado memory usage per target device: `MemoryUsage `__. This problem can be solved if a linux Swap file is created. You can find more information about what a swap file is at this link: `SwapFile `__ To create a swap file you can use the following commands: .. code-block:: bash :~$ sudo fallocate -l "memory size (e.g 1G, 2G, 8G, etc.)" /swapfile :~$ sudo chmod 600 /swapfile :~$ sudo mkswap /swapfile :~$ sudo swapon /swapfile If you want to make the change permanent: .. code-block:: bash # in /etc/fstab file type the command: /swapfile swap swap defaults 0 0 If you want to deactivate the swap memory: .. code-block:: bash :~$ sudo swapoff -v /swapfile .. collapsible:: Building manually in Vivado GUI .. warning:: We do not recommend using this flow, in general people are losing a lot of valuable time and nerve during this process. In Vivado (AMD projects), **you must build all the required libraries** for your targeted project. Open the GUI and at the TCL console change the directory to where the libraries are, then source the **\_ip.tcl** file. .. code-block:: cd c:/github/hdl/library/axi_ltc2387 source ./axi_ltc2387_ip.tcl You will see commands being executed, and the GUI will change into a project window. There is nothing to do here, you could browse the source if you prefer to do synthesis as stand-alone and such things. After you're done, quit and change the directory to the next library and continue the process. After you built all the required libraries for your project, you can run the project (generate bitstream and export the design to SDK). This is the same procedure as above except for changes in path and Tcl file names: .. code-block:: bash cd c:/github/hdl/projects/cn0577/zed source ./system_project.tcl Same behavior as above, the GUI will change into a project window. The script will create a board design in IPI (IP Integrator), generate all the IP targets, synthesize the netlist and implementation. Supported targets of ``make`` command ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .. note:: `Make `__ is a build automation tool, which uses **Makefile(s)** to define a set of directives ('rules') about how to compile and/or link a program ('targets'). In general, always run ``make`` within a project folder such as **hdl/projects/daq2/a10soc** or **hdl/projects/daq2/zc706**. There should not be a need for you to run ``make`` inside the library or root folders. The ``make`` framework passes the top level 'targets' to any sub-makes inside its sub-folders. What this means is that if you run ``make`` inside **hdl/projects/daq2**, it builds all the carriers (**kc705**, **a10soc**, **kcu105**, **zc706** to **zcu102**) instead of just the target carrier. The following 'targets' are supported. +------------------+--------------------------------------------------+ | argument | description | +==================+==================================================+ | all | This builds everything in the current folder and | | | its sub-folders, see context examples below. | +------------------+--------------------------------------------------+ | | make -C library/axi_ad9122 all; ## build AD9122 | | | library component (AMD only). | +------------------+--------------------------------------------------+ | | make -C library all; ## build **ALL** library | | | components inside 'library' (AMD only). | +------------------+--------------------------------------------------+ | | make -C projects/daq2/zc706 all; ## build | | | DAQ2_ZC706 (AMD) project. | +------------------+--------------------------------------------------+ | | make -C projects/daq2/a10soc all; ## build | | | DAQ2_A10SOC(Intel) project. | +------------------+--------------------------------------------------+ | | make -C projects/daq2 all; ## build DAQ2 **ALL** | | | carrier (including Intel & AMD) projects. | +------------------+--------------------------------------------------+ | | make -C projects all; ## build **ALL** projects | | | (something you really should NOT do). | +------------------+--------------------------------------------------+ | clean | This removes all tool and temporary files in the | | | current folder and its sub-folders, same context | | | as above. | +------------------+--------------------------------------------------+ | clean-all | This removes all tool and temporary files in the | | | current folder, its sub-folders and from all the | | | IPs that are specified in the Makefile file; | | | same context as above. | +------------------+--------------------------------------------------+ | lib | This is same as 'all' in the library folder, | | | ignored inside project folders. | +------------------+--------------------------------------------------+ | project.platform | This is a special target available only in the | | | 'hdl' root folder and is ignored everywhere | | | else, see syntax below. | +------------------+--------------------------------------------------+ | | make daq2.a10soc ; ## build | | | projects/daq2/a10soc. | +------------------+--------------------------------------------------+ | | make daq2.zc706 ; ## build projects/daq2/zc706. | +------------------+--------------------------------------------------+ Tools and their versions ------------------------------------------------------------------------------- Tools ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ADI provides reference designs for both Intel and AMD. Please note that we have no preference over Intel or AMD; if possible, we try to port the designs on both platforms. However, there are a few things you should be aware of when building the projects. This is NOT a comparison (generic or otherwise)- this is what you should expect and understand when using ADI HDL repository on these tools. **A red text indicates that you must pay extra attention.** .. list-table:: Tools :widths: auto :header-rows: 1 * - Notes - Intel - AMD * - Main tools - Quartus - Vivado * - EDK tools - QSys - IP Integrator * - SDK tools - Eclipse-Nios, Eclipse-DS5 - Eclipse * - Building library - :green:`Do nothing. Quartus only needs the _hw.tcl and QSys parses them whenever invoked` - :red:`Need to build each and every library component. Vivado has its own way of identifying library components. This means you must build ALL the library components first before starting the project. You must re-run these scripts if there are any modifications` * - Building the project - Source the system_project.tcl file - Source the system_project.tcl file * - Timing analysis - The projects are usually tested and should be free of timing errors. There is no straightforward method to verify a timing pass (it usually involves writing a TCL proc by itself) on both the tools. The make build will fail and return with an error if the timing is not met. - The projects are usually tested and should be free of timing errors. There is no straightforward method to verify a timing pass (it usually involves writing a TCL proc by itself) on both the tools. The make build will fail and return with an error if the timing is not met. * - SDK (Microblaze/Nios) - Use SOPCINFO and SOF files - Use XSA file * - SDK (ARM/FPGA combo) - :red:`Not so well-thought procedure. Need to run different tools, manually edit build files etc. The steps involved are running bsp-editor, running make, modifying linker scripts, makefiles and sources, importing to SDK` - :green:`Same procedure as Microblaze` * - Upgrading/Version changes (non-ADI cores) - :green:`Quartus automatically updates the cores. Almost hassle-free for most of the cores` - :red:`Vivado does not automatically update the revisions in TCL flow (it does on GUI). It will stop at the first version mismatch (a rather slow and frustrating process)` Tool versions ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Though the ADI libraries work across different versions of the tools, the projects we provide **may not**. The AMD and Intel IPs may or may not work across versions. We can only assure you that they are tested and **work only for the versions we specify**. The projects are usually upgraded to the latest tools after they are publicly released. The used tool versions can be found in the `release notes `__ for each branch. The script, which builds the project always double checks the used tools version, and notifies the user if he or she is trying to use an unsupported version of tools. .. note:: There are several ways to find out which tool version you should use. The easiest way is to check the `release notes `__. You may also check out or browse the desired branch, and verify the tool version in the base Tcl script (`./hdl/projects/scripts/adi_project_xilinx.tcl `__) or (`./hdl/projects/scripts/adi_project_intel.tcl `__), which build the projects. Environment ------------------------------------------------------------------------------- As said above, our recommended build flow is to use ``make`` and the command line version of the tools. This method facilitates our overall build and release process as it automatically builds the required libraries and dependencies. Linux environment setup ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ All major distributions should have ``make`` installed by default. If not, if you try the command, it should tell you how to install it with the package name. You may have to install ``git`` (``sudo apt-get install git``) and the Intel and AMD tools. These tools come with certain **settings*.sh** scripts that you may source in your **.bashrc** file to set up the environment. You may also do this manually (for better or worse); the following snippet is from a **.bashrc** file. Please note that unless you are an expert at manipulating these things, it is best to leave it to the tools to set up the environment. .. code-block:: bash export PATH=$PATH:/opt/Xilinx/Vivado/202x.x/bin:/opt/Xilinx/Vitis/202x.x/bin export PATH=$PATH:/opt/intelFPGA_pro/2x.x/quartus/bin Windows environment setup ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The best option on Windows is to use `Cygwin `__. When installing it, select the ``make`` and ``git`` packages. The manual changes to your **.bashrc** do a lot look like that of the Linux environment. .. code-block:: bash export PATH=$PATH:/cygdrive/d/Xilinx/Vivado/202x.x/bin:/cygdrive/d/Xilinx/Vitis/202x.x/bin export PATH=$PATH:/cygdrive/d/intelFPGA_pro/2x.x/quartus/bin64 A very good alternative to Cygwin is `WSL `__. The manual changes to your **.bashrc** should look like: .. code-block:: bash export PATH=$PATH:/opt/path_to/Vivado/202x.x/bin:/opt/Vitis/202x.x/bin export PATH=$PATH:/opt/path_to/quartus/bin If you do not want to install Cygwin, there might still be some alternative. There are ``make`` alternatives for **Windows Command Prompt**, minimalist GNU for Windows (**MinGW**), or the **Cygwin variations** installed by the tools itself. Some of these may not be fully functional with our scripts and/or projects. If you are an Intel user, the **Nios II Command Shell** does support make. If you are an AMD user, use the **gnuwin** installed as part of the SDK, usually at ``C:\Xilinx\Vitis\202x.x\gnuwin\bin``. Preparing the SD card ------------------------------------------------------------------------------- Firstly, you have to check this `tutorial `__ on how to put the Linux image on your SD card. Once you are done with that, you can go on with the following steps. On the BOOT partition recently created, you will find folders for each carrier that we support, and each of these folders contain an archive called **bootgen_sysfiles.tgz**. These have all the files needed to generate the **BOOT.BIN**. Copy the corresponding archive (checking for the name of your carrier and components) into the root folder of your project, unzip it twice, and there you will find the files that are needed to generate the **BOOT.BIN**. Copy them to be in the root directory. #. fsbl.elf #. zynq.bif #. u-boot.elf #. and if you're using ZCU102, then bl31.elf and pmu.elf Next, what your project needs, is the **uImage** (for Zynq based carriers) or **Image** (for Zynq UltraScale - ZCU102 and ADRV9009-ZU11EG carriers) or **zImage** (for Intel based carriers) file that you will find in the **zynq-common** or **zynqmp-common**, **socfpga_arria10_common** or **socfpga_cyclone5_common** on your **boot** partition. Copy this file also in the root directory of your project. More info on how to generate this file you will find in the `References`_ section or in the **ReadMe.txt** file from **boot** partition. .. collapsible:: How to build the boot image BOOT.BIN in WSL After obtaining **.xsa** file, you must be sure that you have done source for Vivado and Vitis. To create **boot.bin** is recommended to run ``build_boot_bin.sh`` in terminal.To do this, the file can be called in the following manner: .. code-block:: bash chmod +x build_boot_bin.sh usage: build_boot_bin.sh system_top.xsa u-boot.elf [output-archive] You can download the script by accessing the following link: `build_boot_bin.sh `__. References ------------------------------------------------------------------------------- - `How to build the Zynq boot image BOOT.BIN `__ - `How to build the ZynqMP boot image BOOT.BIN `__ - `Building the ADI Linux kernel `__ Errors, Warnings and Notes ------------------------------------------------------------------------------- Assuming the right to make an honest comment, the tools (both Quartus and Vivado) are not that useful or friendly when it comes to messages. In most cases, you may see **hacked-in** debugging ``printf`` sort of messages (AMD notoriously ranks high in this regard). So you are going to see a lot of **warnings** and some **critical-warnings** (critical to what could be hard to answer). Here are some of the commonly asked EngineerZone questions and their explanations. AMD: Vivado ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .. code-block:: ERROR: [BD 5-216] VLNV is not supported for the current part. ERROR: [Common 17-39] 'create_bd_cell' failed due to earlier errors while executing "create_bd_cell -type ip -vlnv analog.com:user:axi_clkgen:1.0 axi_hdmi_clkgen" invoked from within "set axi_hdmi_clkgen [create_bd_cell -type ip -vlnv analog.com:user:axi_clkgen:1.0 axi_hdmi_clkgen]" (file "../../../projects/common/zc706/zc706_system_bd.tcl" line 57) You haven't generated the library component or have the wrong user IP repository setting. If you were using the GUI flow, now is a good time to evaluate the ``make`` flow. .. code-block:: CRITICAL WARNING: [IP_Flow 19-459] IP file 'C:/Git/hdl/library/common/ad_pnmon.v' appears to be outside of the project area 'C:/Git/hdl/library/axi_ad9467'. You can use the ipx::package_project -import_files option to copy remote files into the IP directory. These warnings appear because the libraries are using common modules which are located under the **./library/common/**. These warnings can be ignored, they won't affect the functionality of the IP or the project. However, you may not be able to archive these projects. The irony is that it does copy these files to the project area, but ignores them. .. _AMD Xilinx Vivado: https://www.xilinx.com/support/download.html .. _Intel Quartus Prime Pro and Standard: https://www.intel.com/content/www/us/en/products/details/fpga/development-tools/quartus-prime/resource.html