// ***************************************************************************
// ***************************************************************************
// Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
//
// This core  is distributed in the hope that it will be useful, but WITHOUT ANY
// WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR
// A PARTICULAR PURPOSE.
//
// Redistribution and use of source or resulting binaries, with or without modification
// of this file, are permitted under one of the following two license terms:
//
//   1. The GNU General Public License version 2 as published by the
//      Free Software Foundation, which can be found in the top level directory of
//      the repository (LICENSE_GPL2), and at: <https://www.gnu.org/licenses/old-licenses/gpl-2.0.html>
//
// OR
//
//   2. An ADI specific BSD license as noted in the top level directory, or on-line at:
//      https://github.com/analogdevicesinc/hdl/blob/master/LICENSE_ADIBSD
//      This will allow to generate bit files and not release the source code,
//      as long as it attaches to an ADI device.
//
// ***************************************************************************
// ***************************************************************************

module dmac_dest_axi_stream (
  input s_axis_aclk,
  input s_axis_aresetn,

  input enable,
  output enabled,
  input sync_id,
  output sync_id_ret,
        output xfer_req,

  input [ID_WIDTH-1:0] request_id,
  output [ID_WIDTH-1:0] response_id,
  output [ID_WIDTH-1:0] data_id,
  input data_eot,
  input response_eot,

  input m_axis_ready,
  output m_axis_valid,
  output [S_AXIS_DATA_WIDTH-1:0] m_axis_data,
        output m_axis_last,

  output fifo_ready,
  input fifo_valid,
  input [S_AXIS_DATA_WIDTH-1:0] fifo_data,

  input req_valid,
  output req_ready,
  input [BEATS_PER_BURST_WIDTH-1:0] req_last_burst_length,
        input req_xlast,

  output response_valid,
  input response_ready,
  output response_resp_eot,
  output [1:0] response_resp
);

parameter ID_WIDTH = 3;
parameter S_AXIS_DATA_WIDTH = 64;
parameter BEATS_PER_BURST_WIDTH = 4;

reg req_xlast_d = 1'b0;

assign sync_id_ret = sync_id;
wire data_enabled;
wire _fifo_ready;
wire m_axis_last_s;

// We are not allowed to just de-assert valid, but if the streaming target does
// not accept any samples anymore we'd lock up the DMA core. So retain the last
// beat when disabled until it is accepted. But if in the meantime the DMA core
// is re-enabled and new data becomes available overwrite the old.

always @(posedge s_axis_aclk) begin
  if(req_ready == 1'b1) begin
    req_xlast_d <= req_xlast;
  end
end

assign m_axis_last = (req_xlast_d == 1'b1) ? m_axis_last_s : 1'b0;

dmac_data_mover # (
  .ID_WIDTH(ID_WIDTH),
  .DATA_WIDTH(S_AXIS_DATA_WIDTH),
  .BEATS_PER_BURST_WIDTH(BEATS_PER_BURST_WIDTH),
  .DISABLE_WAIT_FOR_ID(0),
  .LAST(1)
) i_data_mover (
  .clk(s_axis_aclk),
  .resetn(s_axis_aresetn),

  .enable(enable),
  .enabled(data_enabled),
  .sync_id(sync_id),
        .xfer_req(xfer_req),

  .request_id(request_id),
  .response_id(data_id),
  .eot(data_eot),

  .req_valid(req_valid),
  .req_ready(req_ready),
  .req_last_burst_length(req_last_burst_length),

  .m_axi_ready(m_axis_ready),
  .m_axi_valid(m_axis_valid),
  .m_axi_data(m_axis_data),
        .m_axi_last(m_axis_last_s),
  .s_axi_ready(_fifo_ready),
  .s_axi_valid(fifo_valid),
  .s_axi_data(fifo_data)
);

dmac_response_generator # (
  .ID_WIDTH(ID_WIDTH)
) i_response_generator (
  .clk(s_axis_aclk),
  .resetn(s_axis_aresetn),

  .enable(data_enabled),
  .enabled(enabled),
  .sync_id(sync_id),

  .request_id(data_id),
  .response_id(response_id),

  .eot(response_eot),

  .resp_valid(response_valid),
  .resp_ready(response_ready),
  .resp_eot(response_resp_eot),
  .resp_resp(response_resp)
);

assign fifo_ready = _fifo_ready | ~enabled;

endmodule