pluto_hdl_adi/library/common/up_xfer_cntrl.v

127 lines
4.7 KiB
Verilog

// ***************************************************************************
// ***************************************************************************
// Copyright 2011(c) Analog Devices, Inc.
//
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or without modification,
// are permitted provided that the following conditions are met:
// - Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
// - Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in
// the documentation and/or other materials provided with the
// distribution.
// - Neither the name of Analog Devices, Inc. nor the names of its
// contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
// - The use of this software may or may not infringe the patent rights
// of one or more patent holders. This license does not release you
// from the requirement that you obtain separate licenses from these
// patent holders to use this software.
// - Use of the software either in source or binary form, must be run
// on or directly connected to an Analog Devices Inc. component.
//
// THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
// INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
// PARTICULAR PURPOSE ARE DISCLAIMED.
//
// IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
// EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, INTELLECTUAL PROPERTY
// RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
// STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
// THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
// ***************************************************************************
// ***************************************************************************
`timescale 1ns/100ps
module up_xfer_cntrl #(
parameter DATA_WIDTH = 8) (
// up interface
input up_rstn,
input up_clk,
input [DW:0] up_data_cntrl,
output reg up_xfer_done,
// device interface
input d_rst,
input d_clk,
output reg [DW:0] d_data_cntrl);
localparam DW = DATA_WIDTH - 1;
// internal registers
reg up_xfer_state_m1 = 'd0;
reg up_xfer_state_m2 = 'd0;
reg up_xfer_state = 'd0;
reg [ 5:0] up_xfer_count = 'd0;
reg up_xfer_toggle = 'd0;
reg [DW:0] up_xfer_data = 'd0;
reg d_xfer_toggle_m1 = 'd0;
reg d_xfer_toggle_m2 = 'd0;
reg d_xfer_toggle_m3 = 'd0;
reg d_xfer_toggle = 'd0;
// internal signals
wire up_xfer_enable_s;
wire d_xfer_toggle_s;
// device control transfer
assign up_xfer_enable_s = up_xfer_state ^ up_xfer_toggle;
always @(negedge up_rstn or posedge up_clk) begin
if (up_rstn == 1'b0) begin
up_xfer_state_m1 <= 'd0;
up_xfer_state_m2 <= 'd0;
up_xfer_state <= 'd0;
up_xfer_count <= 'd0;
up_xfer_done <= 'd0;
up_xfer_toggle <= 'd0;
up_xfer_data <= 'd0;
end else begin
up_xfer_state_m1 <= d_xfer_toggle;
up_xfer_state_m2 <= up_xfer_state_m1;
up_xfer_state <= up_xfer_state_m2;
up_xfer_count <= up_xfer_count + 1'd1;
up_xfer_done <= (up_xfer_count == 6'd1) ? ~up_xfer_enable_s : 1'b0;
if ((up_xfer_count == 6'd1) && (up_xfer_enable_s == 1'b0)) begin
up_xfer_toggle <= ~up_xfer_toggle;
up_xfer_data <= up_data_cntrl;
end
end
end
assign d_xfer_toggle_s = d_xfer_toggle_m3 ^ d_xfer_toggle_m2;
always @(posedge d_clk or posedge d_rst) begin
if (d_rst == 1'b1) begin
d_xfer_toggle_m1 <= 'd0;
d_xfer_toggle_m2 <= 'd0;
d_xfer_toggle_m3 <= 'd0;
d_xfer_toggle <= 'd0;
d_data_cntrl <= 'd0;
end else begin
d_xfer_toggle_m1 <= up_xfer_toggle;
d_xfer_toggle_m2 <= d_xfer_toggle_m1;
d_xfer_toggle_m3 <= d_xfer_toggle_m2;
d_xfer_toggle <= d_xfer_toggle_m3;
if (d_xfer_toggle_s == 1'b1) begin
d_data_cntrl <= up_xfer_data;
end
end
end
endmodule
// ***************************************************************************
// ***************************************************************************