216 lines
7.6 KiB
Tcl
216 lines
7.6 KiB
Tcl
###############################################################################
|
|
## Copyright (C) 2021-2023 Analog Devices, Inc. All rights reserved.
|
|
### SPDX short identifier: ADIBSD
|
|
###############################################################################
|
|
|
|
source $ad_hdl_dir/library/spi_engine/scripts/spi_engine.tcl
|
|
# system level parameters
|
|
set NUM_OF_SDI $ad_project_params(NUM_OF_SDI)
|
|
set CAPTURE_ZONE $ad_project_params(CAPTURE_ZONE)
|
|
set CLK_MODE $ad_project_params(CLK_MODE)
|
|
set DDR_EN $ad_project_params(DDR_EN)
|
|
|
|
puts "build parameters: NUM_OF_SDI: $NUM_OF_SDI ; CAPTURE_ZONE: $CAPTURE_ZONE ; CLK_MODE: $CLK_MODE ;DDR_EN: $DDR_EN"
|
|
|
|
# block design ports and interfaces
|
|
# specify the CNV generator's reference clock frequency in MHz
|
|
# NOTE: this is a default value, software may or may not change this
|
|
set cnv_ref_clk 100
|
|
|
|
# specify ADC sampling rate in samples/seconds
|
|
# NOTE: this is a default value, software may or may not change this
|
|
set adc_sampling_rate 1000000
|
|
|
|
#create_bd_intf_port -mode Master -vlnv analog.com:interface:spi_master_rtl:1.0 ad463x_spi
|
|
|
|
create_bd_port -dir O ad463x_spi_sclk
|
|
create_bd_port -dir O ad463x_spi_cs
|
|
create_bd_port -dir O ad463x_spi_sdo
|
|
create_bd_port -dir I -from [expr $NUM_OF_SDI-1] -to 0 ad463x_spi_sdi
|
|
|
|
create_bd_port -dir I ad463x_echo_sclk
|
|
|
|
create_bd_port -dir I ad463x_busy
|
|
create_bd_port -dir O ad463x_cnv
|
|
create_bd_port -dir I ad463x_ext_clk
|
|
|
|
## To support the 2MSPS (SCLK == 80 MHz), set the spi clock to 160 MHz
|
|
|
|
ad_ip_instance axi_clkgen spi_clkgen
|
|
ad_ip_parameter spi_clkgen CONFIG.CLK0_DIV 5
|
|
ad_ip_parameter spi_clkgen CONFIG.VCO_DIV 1
|
|
ad_ip_parameter spi_clkgen CONFIG.VCO_MUL 8
|
|
ad_connect $sys_cpu_clk spi_clkgen/clk
|
|
ad_connect spi_clk spi_clkgen/clk_0
|
|
|
|
# create a SPI Engine architecture
|
|
|
|
#spi_engine_create "spi_ad463x" 32 1 1 $NUM_OF_SDI 0 1
|
|
|
|
set data_width 32
|
|
set async_spi_clk 1
|
|
set num_cs 1
|
|
set num_sdi $NUM_OF_SDI
|
|
set num_sdo 1
|
|
set sdi_delay 1
|
|
set echo_sclk 1
|
|
|
|
set hier_spi_engine spi_ad463x
|
|
|
|
spi_engine_create $hier_spi_engine $data_width $async_spi_clk $num_cs $num_sdi $num_sdo $sdi_delay $echo_sclk
|
|
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_execution CONFIG.DEFAULT_SPI_CFG 1 ; # latching MISO on negative edge - hardware only
|
|
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_axi_regmap CONFIG.CFG_INFO_0 $NUM_OF_SDI
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_axi_regmap CONFIG.CFG_INFO_1 $CAPTURE_ZONE
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_axi_regmap CONFIG.CFG_INFO_2 $CLK_MODE
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_axi_regmap CONFIG.CFG_INFO_3 $DDR_EN
|
|
|
|
## to setup the sample rate of the system change the PULSE_PERIOD value of the
|
|
## CNV generator; the actual sample rate will be PULSE_PERIOD * (1/cnv_ref_clk)
|
|
set sampling_cycle [expr int(ceil(double($cnv_ref_clk * 1000000) / $adc_sampling_rate))]
|
|
|
|
ad_ip_instance axi_pwm_gen cnv_generator
|
|
ad_ip_parameter cnv_generator CONFIG.N_PWMS 2
|
|
ad_ip_parameter cnv_generator CONFIG.PULSE_0_PERIOD $sampling_cycle
|
|
ad_ip_parameter cnv_generator CONFIG.PULSE_0_WIDTH 1
|
|
ad_ip_parameter cnv_generator CONFIG.PULSE_1_PERIOD $sampling_cycle
|
|
ad_ip_parameter cnv_generator CONFIG.PULSE_1_WIDTH 1
|
|
ad_ip_parameter cnv_generator CONFIG.PULSE_1_OFFSET 1
|
|
|
|
ad_ip_instance spi_axis_reorder data_reorder
|
|
ad_ip_parameter data_reorder CONFIG.NUM_OF_LANES $NUM_OF_SDI
|
|
|
|
# dma to receive data stream
|
|
|
|
ad_ip_instance axi_dmac axi_ad463x_dma
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.DMA_TYPE_SRC 1
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.DMA_TYPE_DEST 0
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.CYCLIC 0
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.AXI_SLICE_DEST 1
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.AXI_SLICE_SRC 1
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.DMA_DATA_WIDTH_SRC 64
|
|
ad_ip_parameter axi_ad463x_dma CONFIG.DMA_DATA_WIDTH_DEST 64
|
|
|
|
# Trigger for SPI offload
|
|
if {$CAPTURE_ZONE == 1} {
|
|
|
|
## SPI mode is using the echo SCLK, on echo SPI and Master mode the BUSY
|
|
# is used for SDI latching
|
|
switch $CLK_MODE {
|
|
0 {
|
|
ad_connect $hier_spi_engine/echo_sclk ad463x_echo_sclk
|
|
}
|
|
1 -
|
|
2 {
|
|
puts "ERROR: Invalid configuration option. CAPTURE_ZONE 1 can be used only in SPI mode (CLK_MODE == 1)."
|
|
exit 2
|
|
}
|
|
default {
|
|
puts "ERROR: Invalid value for CLK_MODE. (valid values are 0 or 1 or 2)"
|
|
exit 2
|
|
}
|
|
}
|
|
|
|
# Zone 1 - trigger to BUSY's negative edge
|
|
create_bd_cell -type module -reference sync_bits busy_sync
|
|
create_bd_cell -type module -reference ad_edge_detect busy_capture
|
|
set_property -dict [list CONFIG.EDGE 1] [get_bd_cells busy_capture]
|
|
|
|
ad_connect spi_clk busy_capture/clk
|
|
ad_connect spi_clk busy_sync/out_clk
|
|
ad_connect busy_capture/rst GND
|
|
ad_connect $hier_spi_engine/${hier_spi_engine}_axi_regmap/spi_resetn busy_sync/out_resetn
|
|
|
|
ad_connect ad463x_busy busy_sync/in_bits
|
|
ad_connect busy_sync/out_bits busy_capture/signal_in
|
|
ad_connect $hier_spi_engine/trigger busy_capture/signal_out
|
|
## SDI is latched by the SPIE execution module
|
|
ad_connect $hier_spi_engine/m_axis_sample data_reorder/s_axis
|
|
|
|
} elseif {$CAPTURE_ZONE == 2} {
|
|
|
|
# Zone 2 - trigger to next consecutive CNV
|
|
ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_offload CONFIG.ASYNC_TRIG 1
|
|
ad_connect cnv_generator/pwm_0 $hier_spi_engine/trigger
|
|
|
|
## SPI mode is using the echo SCLK, on echo SPI and Master mode the BUSY
|
|
# is used for SDI latching
|
|
|
|
ad_connect $hier_spi_engine/echo_sclk ad463x_echo_sclk
|
|
switch $CLK_MODE {
|
|
0 {
|
|
## SDI is latched by the SPIE execution module
|
|
ad_connect $hier_spi_engine/m_axis_sample data_reorder/s_axis
|
|
}
|
|
1 -
|
|
2 {
|
|
## SDI is latched by the data capture
|
|
ad_ip_instance ad463x_data_capture data_capture
|
|
ad_ip_parameter data_capture CONFIG.DDR_EN $DDR_EN
|
|
ad_ip_parameter data_capture CONFIG.NUM_OF_LANES $NUM_OF_SDI
|
|
|
|
ad_connect spi_clk data_capture/clk
|
|
ad_connect ad463x_spi_cs data_capture/csn
|
|
ad_connect ad463x_busy data_capture/echo_sclk
|
|
ad_connect ad463x_spi_sdi data_capture/data_in
|
|
|
|
ad_connect data_capture/m_axis data_reorder/s_axis
|
|
|
|
}
|
|
default {
|
|
puts "ERROR: Invalid value for CLK_MODE. (valid values are 0 or 1 or 2)"
|
|
exit 2
|
|
}
|
|
}
|
|
|
|
} else {
|
|
|
|
puts "ERROR: Invalid capture zone, please choose 1 or 2."
|
|
exit 2
|
|
|
|
}
|
|
ad_connect ad463x_cnv cnv_generator/pwm_1
|
|
|
|
# clocks
|
|
|
|
ad_connect $sys_cpu_clk $hier_spi_engine/clk
|
|
ad_connect $sys_cpu_clk cnv_generator/s_axi_aclk
|
|
ad_connect spi_clk $hier_spi_engine/spi_clk
|
|
ad_connect spi_clk data_reorder/axis_aclk
|
|
ad_connect spi_clk axi_ad463x_dma/s_axis_aclk
|
|
ad_connect ad463x_ext_clk cnv_generator/ext_clk
|
|
|
|
# resets
|
|
|
|
ad_connect $sys_cpu_resetn cnv_generator/s_axi_aresetn
|
|
ad_connect data_reorder/axis_aresetn VCC
|
|
ad_connect $sys_cpu_resetn $hier_spi_engine/resetn
|
|
ad_connect $sys_cpu_resetn axi_ad463x_dma/m_dest_axi_aresetn
|
|
|
|
# data path
|
|
|
|
ad_connect $hier_spi_engine/${hier_spi_engine}_execution/cs ad463x_spi_cs
|
|
ad_connect $hier_spi_engine/${hier_spi_engine}_execution/sclk ad463x_spi_sclk
|
|
ad_connect $hier_spi_engine/${hier_spi_engine}_execution/sdo ad463x_spi_sdo
|
|
ad_connect $hier_spi_engine/${hier_spi_engine}_execution/sdi ad463x_spi_sdi
|
|
|
|
ad_connect axi_ad463x_dma/s_axis data_reorder/m_axis
|
|
|
|
# AXI memory mapped address space
|
|
|
|
ad_cpu_interconnect 0x44a00000 $hier_spi_engine/${hier_spi_engine}_axi_regmap
|
|
ad_cpu_interconnect 0x44b00000 cnv_generator
|
|
ad_cpu_interconnect 0x44a30000 axi_ad463x_dma
|
|
ad_cpu_interconnect 0x44a70000 spi_clkgen
|
|
|
|
# interrupts
|
|
|
|
ad_cpu_interrupt "ps-13" "mb-13" axi_ad463x_dma/irq
|
|
ad_cpu_interrupt "ps-12" "mb-12" $hier_spi_engine/irq
|
|
|
|
# interconnect to memory interface
|
|
|
|
ad_mem_hp2_interconnect sys_cpu_clk sys_ps7/S_AXI_HP2
|
|
ad_mem_hp2_interconnect sys_cpu_clk axi_ad463x_dma/m_dest_axi
|