zcy
/
pluto_hdl_adi
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
pluto_hdl_adi/docs/regmap/adi_regmap_adc.txt

1002 lines
23 KiB
Plaintext
Raw Blame History

This file contains invisible Unicode characters!

This file contains invisible Unicode characters that may be processed differently from what appears below. If your use case is intentional and legitimate, you can safely ignore this warning. Use the Escape button to reveal hidden characters.

TITLE
ADC Common (axi_ad*)
ADC_COMMON
ENDTITLE
############################################################################################
############################################################################################
REG
0x0010
REG_RSTN
ADC Interface Control & Status
ENDREG
FIELD
[2] 0x0
CE_N
RW
Clock enable, default is enabled(0x0). An inverse version of the signal is exported out of
the module to control clock enables
ENDFIELD
FIELD
[1] 0x0
MMCM_RSTN
RW
MMCM reset only (required for DRP access).
Reset, default is IN-RESET (0x0), software must write 0x1 to bring up the core.
ENDFIELD
FIELD
[0] 0x0
RSTN
RW
Reset, default is IN-RESET (0x0), software must write 0x1 to bring up the core.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0011
REG_CNTRL
ADC Interface Control & Status
ENDREG
FIELD
[16] 0x0
SDR_DDR_N
RW
Interface type (1 represents SDR, 0 represents DDR)
ENDFIELD
FIELD
[15] 0x0
SYMB_OP
RW
Select symbol data format mode (0x1)
ENDFIELD
FIELD
[14] 0x0
SYMB_8_16B
RW
Select number of bits for symbol format mode (1 represents 8b, 0 represents 16b)
ENDFIELD
FIELD
[12:8] 0x0
NUM_LANES[4:0]
RW
Number of active lanes (1 : CSSI 1-lane, LSSI 1-lane, 2 : LSSI 2-lane, 4 : CSSI 4-lane).
For AD7768, AD7768-4 and AD777x number of active lanes : 1/2/4/8 where supported.
ENDFIELD
FIELD
[3] 0x0
SYNC
RW
Initialize synchronization between multiple ADCs
ENDFIELD
FIELD
[2] 0x0
R1_MODE
RW
Select number of RF channels 1 (0x1) or 2 (0x0).
ENDFIELD
FIELD
[1] 0x0
DDR_EDGESEL
RW
Select rising edge (0x0) or falling edge (0x1) for the first part
of a sample (if applicable) followed by the successive edges for
the remaining parts. This only controls how the sample is delineated
from the incoming data post DDR registers.
ENDFIELD
FIELD
[0] 0x0
PIN_MODE
RW
Select interface pin mode to be clock multiplexed (0x1) or pin
multiplexed (0x0). In clock multiplexed mode, samples are received
on alternative clock edges. In pin multiplexed mode, samples are
interleaved or grouped on the pins at the same clock edge.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0012
REG_CNTRL_2
ADC Interface Control & Status
ENDREG
FIELD
[1] 0x0
EXT_SYNC_ARM
RW
Setting this bit will arm the trigger mechanism sensitive to an external sync signal.
Once the external sync signal goes high it synchronizes channels within a ADC, and across multiple instances.
This bit has an effect only the EXT_SYNC synthesis parameter is set.
This bit self clears.
ENDFIELD
FIELD
[2] 0x0
EXT_SYNC_DISARM
RW
Setting this bit will disarm the trigger mechanism sensitive to an external sync signal.
This bit has an effect only the EXT_SYNC synthesis parameter is set.
This bit self clears.
ENDFIELD
FIELD
[8] 0x0
MANUAL_SYNC_REQUEST
RW
Setting this bit will issue an external sync event if it is hooked up inside the fabric.
This bit has an effect only the EXT_SYNC synthesis parameter is set.
This bit self clears.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0013
REG_CNTRL_3
ADC Interface Control & Status
ENDREG
FIELD
[8] 0x0
CRC_EN
RW
Setting this bit will enable the CRC generation.
ENDFIELD
FIELD
[7:0] 0x00
CUSTOM_CONTROL
RW
Select output format decode mode.(for ADAQ8092: bit 0 - enables digital output randomizer decode
, bit 1 - enables alternate bit polarity decode).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0015
REG_CLK_FREQ
ADC Interface Control & Status
ENDREG
FIELD
[31:0] 0x0000
CLK_FREQ[31:0]
RO
Interface clock frequency. This is relative to the processor clock and in many cases is
100MHz. The number is represented as unsigned 16.16 format. Assuming a 100MHz processor
clock the minimum is 1.523kHz and maximum is 6.554THz. The actual interface clock
is CLK_FREQ * CLK_RATIO (see below). Note that the actual sampling clock may not be
the same as the interface clock- software must consider device specific implementation
parameters to calculate the final sampling clock.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0016
REG_CLK_RATIO
ADC Interface Control & Status
ENDREG
FIELD
[31:0] 0x0000
CLK_RATIO[31:0]
RO
Interface clock ratio - as a factor actual received clock. This is implementation specific
and depends on any serial to parallel conversion and interface type (ddr/sdr/qdr).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0017
REG_STATUS
ADC Interface Control & Status
ENDREG
FIELD
[4] 0x0
ADC_CTRL_STATUS
RO
If set, indicates that the device'​s register data is available on the data bus.
ENDFIELD
FIELD
[3] 0x0
PN_ERR
RO
If set, indicates pn error in one or more channels.
ENDFIELD
FIELD
[2] 0x0
PN_OOS
RO
If set, indicates pn oos in one or more channels.
ENDFIELD
FIELD
[1] 0x0
OVER_RANGE
RO
If set, indicates over range in one or more channels.
ENDFIELD
FIELD
[0] 0x0
STATUS
RO
Interface status, if set indicates no errors. If not set, there
are errors, software may try resetting the cores.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0018
REG_DELAY_CNTRL
ADC Interface Control & Status(''Deprecated from version 9'')
ENDREG
FIELD
[17] 0x0
DELAY_SEL
RW
Delay select, a 0x0 to 0x1 transition in this register initiates
a delay access controlled by the registers below.
ENDFIELD
FIELD
[16] 0x0
DELAY_RWN
RW
Delay read (0x1) or write (0x0), the delay is accessed directly
(no increment or decrement) with an address corresponding to each pin,
and data corresponding to the total delay.
ENDFIELD
FIELD
[15:8] 0x00
DELAY_ADDRESS[7:0]
RW
Delay address, the range depends on the interface pins, data pins
are usually at the lower range.
ENDFIELD
FIELD
[4:0] 0x0
DELAY_WDATA[4:0]
RW
Delay write data, a value of 1 corresponds to (1/200)ns for most devices.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0019
REG_DELAY_STATUS
ADC Interface Control & Status(''Deprecated from version 9'')
ENDREG
FIELD
[9] 0x0
DELAY_LOCKED
RO
Indicates delay locked (0x1) state. If this bit is read 0x0, delay control
has failed to calibrate the elements.
ENDFIELD
FIELD
[8] 0x0
DELAY_STATUS
RO
If set, indicates busy status (access pending). The read data may not be
valid if this bit is set.
ENDFIELD
FIELD
[4:0] 0x0
DELAY_RDATA[4:0]
RO
Delay read data, current delay value in the elements
ENDFIELD
############################################################################################
############################################################################################
REG
0x001A
REG_SYNC_STATUS
ADC Synchronization Status register
ENDREG
FIELD
[0] 0x0
ADC_SYNC
RO
ADC synchronization status. Will be set to 1 after the synchronization has been completed
or while waiting for the synchronization signal in JESD204 systems.
ENDFIELD
############################################################################################
############################################################################################
REG
0x001C
REG_DRP_CNTRL
ADC Interface Control & Status
ENDREG
FIELD
[28] 0x0
DRP_RWN
RW
DRP read (0x1) or write (0x0) select (does not include GTX lanes).
NOT-APPLICABLE if DRP_DISABLE is set (0x1).
ENDFIELD
FIELD
[27:16] 0x00
DRP_ADDRESS[11:0]
RW
DRP address, designs that contain more than one DRP accessible primitives
have selects based on the most significant bits (does not include GTX lanes).
NOT-APPLICABLE if DRP_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:0] 0x0000
RESERVED[15:0]
RO
Reserved for backward compatibility.
ENDFIELD
############################################################################################
############################################################################################
REG
0x001D
REG_DRP_STATUS
ADC Interface Control & Status
ENDREG
FIELD
[17] 0x0
DRP_LOCKED
RO
If set indicates that the DRP has been locked.
ENDFIELD
FIELD
[16] 0x0
DRP_STATUS
RO
If set indicates busy (access pending). The read data may not be valid if
this bit is set (does not include GTX lanes).
NOT-APPLICABLE if DRP_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:0] 0x00
RESERVED[15:0]
RO
Reserved for backward compatibility.
ENDFIELD
############################################################################################
############################################################################################
REG
0x001E
REG_DRP_WDATA
ADC DRP Write Data
ENDREG
FIELD
[15:0] 0x00
DRP_WDATA[15:0]
RW
DRP write data (does not include GTX lanes).
NOT-APPLICABLE if DRP_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x001F
REG_DRP_RDATA
ADC DRP Read Data
ENDREG
FIELD
[15:0] 0x00
DRP_RDATA[15:0]
RO
DRP read data (does not include GTX lanes).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0020
REG_ADC_CONFIG_WR
ADC Write Configuration ​Data
ENDREG
FIELD
[31:0] 0x0000
ADC_CONFIG_WR[31:0]
RW
Custom ​Write to the available registers.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0021
REG_ADC_CONFIG_RD
ADC Read Configuration ​Data
ENDREG
FIELD
[31:0] 0x0000
ADC_CONFIG_RD[31:0]
RO
Custom read of the available registers.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0022
REG_UI_STATUS
User Interface Status
ENDREG
FIELD
[2] 0x0
UI_OVF
RW1C
User Interface overflow. If set, indicates an overflow occurred during data transfer at
the user interface (FIFO interface). Software must write a 0x1 to clear this register
bit.
ENDFIELD
FIELD
[1] 0x0
UI_UNF
RW1C
User Interface underflow. If set, indicates an underflow occurred during data transfer at
the user interface (FIFO interface). Software must write a 0x1 to clear this register
bit.
ENDFIELD
FIELD
[0] 0x0
UI_RESERVED
RW1C
Reserved for backward compatibility.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0023
REG_ADC_CONFIG_CTRL
ADC RD/WR configuration
ENDREG
FIELD
[31:0] 0x0000
ADC_CONFIG_CTRL[31:​0]
RW
Control RD/WR requests to the device'​s register map: bit 1 - RD ('b1) , WR ('b0), bit 0 - enable WR/RD operation.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0028
REG_USR_CNTRL_1
ADC Interface Control & Status
ENDREG
FIELD
[7:0] 0x00
USR_CHANMAX[7:0]
RW
This indicates the maximum number of inputs for the channel data multiplexers. User may add
different processing modules post data capture as another input to this common multiplexer.
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0029
REG_ADC_START_CODE
ADC Synchronization start word
ENDREG
FIELD
[31:0] 0x00000000
ADC_START_CODE[31:0]
RW
This sets the startcode that is used by the ADCs for synchronization
NOT-APPLICABLE if START_CODE_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x002E
REG_ADC_GPIO_IN
ADC GPIO inputs
ENDREG
FIELD
[31:0] 0x00000000
ADC_GPIO_IN[31:0]
RO
This reads auxiliary GPI pins of the ADC core
ENDFIELD
REG
0x002F
REG_ADC_GPIO_OUT
ADC GPIO outputs
ENDREG
FIELD
[31:0] 0x00000000
ADC_GPIO_OUT[31:0]
RW
This controls auxiliary GPO pins of the ADC core
NOT-APPLICABLE if GPIO_DISABLE is set (0x1).
ENDFIELD
REG
0x0030
REG_PPS_COUNTER
PPS Counter register
ENDREG
FIELD
[31:0] 0x00000000
PPS_COUNTER[31:0]
RO
Counts the core clock cycles (can be a device clock or interface clock) between two 1PPS pulse.
ENDFIELD
REG
0x0031
REG_PPS_STATUS
PPS Status register
ENDREG
FIELD
[0] 0x0
PPS_STATUS
RO
If this bit is asserted there is no incomming 1PPS signal. Maybe the source is out of sync or it's not active.
ENDFIELD
############################################################################################
############################################################################################
TITLE
ADC Channel (axi_ad*)
ADC_CHANNEL
ENDTITLE
############################################################################################
############################################################################################
REG
0x0100
REG_CHAN_CNTRL
ADC Interface Control & Status
ENDREG
FIELD
[11] 0x0
ADC_LB_OWR
RW
If set, forces ADC_DATA_SEL to 1, enabling data loopback
ENDFIELD
FIELD
[10] 0x0
ADC_PN_SEL_OWR
RW
If set, forces ADC_PN_SEL to 0x9, device specific pn (e.g. ad9361)
If both ADC_PN_TYPE_OWR and ADC_PN_SEL_OWR are set, they are ignored
ENDFIELD
FIELD
[9] 0x0
IQCOR_ENB
RW
if set, enables IQ correction or scale correction.
NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
ENDFIELD
FIELD
[8] 0x0
DCFILT_ENB
RW
if set, enables DC filter (to disable DC offset, set offset value to 0x0).
NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
ENDFIELD
FIELD
[6] 0x0
FORMAT_SIGNEXT
RW
if set, enables sign extension (applicable only in 2's complement mode). The data is
always sign extended to the nearest byte boundary.
NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
ENDFIELD
FIELD
[5] 0x0
FORMAT_TYPE
RW
Select offset binary (0x1) or 2's complement (0x0) data type. This sets the incoming
data type and is required by the post processing modules for any data conversion.
NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
ENDFIELD
FIELD
[4] 0x0
FORMAT_ENABLE
RW
Enable data format conversion (see register bits above).
NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
ENDFIELD
FIELD
[3] 0x0
RESERVED
RO
Reserved for backward compatibility.
ENDFIELD
FIELD
[2] 0x0
RESERVED
RO
Reserved for backward compatibility.
ENDFIELD
FIELD
[1] 0x0
ADC_PN_TYPE_OWR
RW
If set, forces ADC_PN_SEL to 0x1, modified pn23
If both ADC_PN_TYPE_OWR and ADC_PN_SEL_OWR are set, they are ignored
ENDFIELD
FIELD
[0] 0x0
ENABLE
RW
If set, enables channel. A 0x0 to 0x1 transition transfers all the control signals
to the respective channel processing module. If a channel is part of a complex
signal (I/Q), even channel is the master and the odd channel is the slave.
Though a single control is used, both must be individually selected.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0101
REG_CHAN_STATUS
ADC Interface Control & Status
ENDREG
FIELD
[12] 0x0
CRC_ERR
RW1C
CRC errors. If set, indicates CRC error. Software must first clear this bit before initiating a transfer and monitor afterwards.
ENDFIELD
FIELD
[11:4] 0x00
STATUS_HEADER
RO
The status header sent by the ADC.(compatible with AD7768/AD7768-4/AD777x).
ENDFIELD
FIELD
[2] 0x0
PN_ERR
RW1C
PN errors. If set, indicates spurious mismatches in sync state. This bit is cleared
if OOS is set and is only indicates errors when OOS is cleared.
ENDFIELD
FIELD
[1] 0x0
PN_OOS
RW1C
PN Out Of Sync. If set, indicates an OOS status. OOS is set, if 64 consecutive patterns
mismatch from the expected pattern. It is cleared, when 16 consecutive patterns match
the expected pattern.
ENDFIELD
FIELD
[0] 0x0
OVER_RANGE
RW1C
If set, indicates over range. Note that over range is independent of the data path,
it indicates an over range over a data transfer period. Software must first clear
this bit before initiating a transfer and monitor afterwards.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0102
REG_CHAN_RAW_DATA
ADC Raw Data Reading
ENDREG
FIELD
[31:0] 0x0000
ADC_READ_DATA[31:0]
RO
Raw data read from the ADC.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0104
REG_CHAN_CNTRL_1
ADC Interface Control & Status
ENDREG
FIELD
[31:16] 0x0000
DCFILT_OFFSET[15:0]
RW
DC removal (if equipped) offset. This is a 2's complement number added to the incoming
data to remove a known DC offset.
NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:0] 0x0000
DCFILT_COEFF[15:0]
RW
DC removal filter (if equipped) coefficient. The format is 1.1.14 (sign, integer and
fractional bits).
NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0105
REG_CHAN_CNTRL_2
ADC Interface Control & Status
ENDREG
FIELD
[31:16] 0x0000
IQCOR_COEFF_1[15:0]
RW
IQ correction (if equipped) coefficient. If scale & offset is implemented, this is the scale value
and the format is 1.1.14 (sign, integer and fractional bits). If matrix multiplication is used,
this is the channel I coefficient and the format is 1.1.14 (sign, integer and fractional bits).
If SCALECORRECTION_ONLY is set, this implements the scale value correction for the current channel
with the format 1.1.14 (sign, integer and fractional bits).
NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:0] 0x0000
IQCOR_COEFF_2[15:0]
RW
IQ correction (if equipped) coefficient. If scale & offset is implemented, this is the offset value
and the format is 2's complement. If matrix multiplication is used, this is the channel Q coefficient
and the format is 1.1.14 (sign, integer and fractional bits).
NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0106
REG_CHAN_CNTRL_3
ADC Interface Control & Status
ENDREG
FIELD
[19:16] 0x0
ADC_PN_SEL[3:0]
RW
Selects the PN monitor sequence type (available only if ADC supports it). \\
- 0x0: pn9a (device specific, modified pn9) \\
- 0x1: pn23a (device specific, modified pn23) \\
- 0x4: pn7 (standard O.150) \\
- 0x5: pn15 (standard O.150) \\
- 0x6: pn23 (standard O.150) \\
- 0x7: pn31 (standard O.150) \\
- 0x9: pnX (device specific, e.g. ad9361) \\
- 0x0A: Nibble ramp (Device specific e.g. adrv9001) \\
- 0x0B: 16 bit ramp (Device specific e.g. adrv9001) \\
ENDFIELD
FIELD
[3:0] 0x0
ADC_DATA_SEL[3:0]
RW
Selects the data source to DMA.
0x0: input data (ADC)
0x1: loopback data (DAC)
ENDFIELD
############################################################################################
############################################################################################
REG
0x0108
REG_CHAN_USR_CNTRL_1
ADC Interface Control & Status
ENDREG
FIELD
[25] 0x0
USR_DATATYPE_BE
RO
The user data type format- if set, indicates big endian (default is little endian).
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
FIELD
[24] 0x0
USR_DATATYPE_SIGNED
RO
The user data type format- if set, indicates signed (2's complement) data (default is unsigned).
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
FIELD
[23:16] 0x00
USR_DATATYPE_SHIFT[7:0]
RO
The user data type format- the amount of right shift for actual samples within the total number
of bits.
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:8] 0x00
USR_DATATYPE_TOTAL_BITS[7:0]
RO
The user data type format- number of total bits used for a sample. The total number of bits must
be an integer multiple of 8 (byte aligned).
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
FIELD
[7:0] 0x00
USR_DATATYPE_BITS[7:0]
RO
The user data type format- number of bits in a sample. This indicates the actual sample data bits.
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x0109
REG_CHAN_USR_CNTRL_2
ADC Interface Control & Status
ENDREG
FIELD
[31:16] 0x0000
USR_DECIMATION_M[15:0]
RW
This holds the user decimation M value of the channel that is currently being selected on
the multiplexer above. The total decimation factor is of the form M/N.
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
FIELD
[15:0] 0x0000
USR_DECIMATION_N[15:0]
RW
This holds the user decimation N value of the channel that is currently being selected on
the multiplexer above. The total decimation factor is of the form M/N.
NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
ENDFIELD
############################################################################################
############################################################################################
REG
0x010A
REG_CHAN_CNTRL_4
ADC Interface Control & Status
ENDREG
FIELD
[31:3] 0x00000000
RESERVED[28:0]
RO
Reserved for backward compatibility.
ENDFIELD
FIELD
[2:0] 0x7
SOFTSPAN [2:0]
RW
Softspan configuration register.
ENDFIELD
############################################################################################
############################################################################################
REG
0x0110
REG_*
Channel 1, similar to register 0x100 to 0x10f.
ENDREG
REG
0x0120
REG_*
Channel 2, similar to register 0x100 to 0x10f.
ENDREG
REG
0x01F0
REG_*
Channel 15, similar to register 0x100 to 0x10f.
ENDREG
############################################################################################
############################################################################################
Reference in New Issue View Git Blame Copy Permalink