375 lines
14 KiB
ReStructuredText
375 lines
14 KiB
ReStructuredText
.. _ad4630_fmc:
|
||
|
||
AD4630-FMC HDL project
|
||
=================================================================================
|
||
|
||
Overview
|
||
---------------------------------------------------------------------------------
|
||
|
||
The :adi:`AD4630-24` is a two-channel, simultaneous sampling, Easy Drive, 2 MSPS
|
||
successive approximation register (SAR) analog-to-digital converter (ADC). The
|
||
:adi:`AD4030-24` is the single channel version. With a guaranteed maximum ±0.9
|
||
ppm INL and no missing codes at 24-bits, the :adi:`AD4630-24` and
|
||
:adi:`AD4030-24` achieve unparalleled precision from −40°C to +125°C.
|
||
The :adi:`AD4030-16` is a 16-bit dual channel version.
|
||
|
||
A low-drift, internal precision reference buffer eases voltage reference
|
||
sharing with other system circuitry. The AD4630-24 offers a typical dynamic
|
||
range of 106 dB when using a 5 V reference. The :adi:`AD4030-24` offers a typical
|
||
dynamic range of 109 dB using a 5 V reference. The low noise floor enables signal
|
||
chains requiring less gain and lower power. A block averaging filter with
|
||
programmable decimation ratio can increase dynamic range up to 153 dB and
|
||
155.5dB for the :adi:`AD4030`. The wide differential input and common mode ranges
|
||
allow inputs to use the full ±VREF range without saturating, simplifying signal
|
||
conditioning requirements and system calibration. The improved settling of the
|
||
Easy Drive analog inputs broadens the selection of analog front-end components
|
||
compatible with the :adi:`AD4630-24`, :adi:`AD4630-16` and :adi:`AD4030-24`.
|
||
Both single-ended and differential signals are supported.
|
||
|
||
The versatile Flexi-SPI serial interface eases host processor and ADC
|
||
integration. A wide data clocking window, multiple SDO lanes, and optional DDR
|
||
data clocking can reduce the serial clock to 10 MHz while operating at a
|
||
sample rate of 2 MSPS. Echo clock mode and ADC master clock mode relax the
|
||
timing requirements and simplify the use of digital isolators.
|
||
|
||
The :adi:`AD4630-24`'s, :adi:`AD4630-16`'s and :adi:`AD4030-24`'s BGA package
|
||
integrates all critical power supply and reference bypass capacitors, reducing
|
||
the footprint and system component count, and lessening sensitivity to board
|
||
layout.
|
||
|
||
The HDL reference design for the :adi:`EVAL-AD4630_FMCZ` and
|
||
:adi:`EVAL-AD4030_FMCZ` provides all the interfaces that are necessary to
|
||
interact with the device using a Xilinx FPGA development board. The design has
|
||
all the necessary infrastructure to acquire data from the :adi:`AD4630-24`
|
||
24-bit dual-channel precision SAR ADC, :adi:`AD4630-16` 16-bit dual channel
|
||
precision SAR ADC and :adi:`AD4030-24` single channel ADC, supporting
|
||
continuous data capture at maximum 2 MSPS data rate. The design targeted to the
|
||
Zedboard, which is a low cost FPGA carrier board from Digilent, using a
|
||
Zynq-7000 re-programmable SoC from Xilinx.
|
||
|
||
Applications:
|
||
* Automatic test equipment
|
||
* Digital control loops
|
||
* Medical instrumentation
|
||
* Seismology
|
||
* Semiconductor manufacturing
|
||
* Scientific instrumentation
|
||
|
||
Supported boards
|
||
-------------------------------------------------------------------------------
|
||
|
||
- :adi:`EVAL-AD4030-24FMCZ <EVAL-AD4030-24FMCZ>`
|
||
- :adi:`EVAL-AD4630-16FMCZ <EVAL-AD4630-16FMCZ>`
|
||
- :adi:`EVAL-AD4630-24FMCZ <EVAL-AD4630-24FMCZ>`
|
||
|
||
Supported devices
|
||
-------------------------------------------------------------------------------
|
||
|
||
- :adi:`AD4030-24`
|
||
- :adi:`AD4630-16`
|
||
- :adi:`AD4630-24`
|
||
|
||
Supported carriers
|
||
-------------------------------------------------------------------------------
|
||
|
||
- :xilinx:`ZedBoard <products/boards-and-kits/1-8dyf-11.html>` on FMC slot
|
||
|
||
Block design
|
||
---------------------------------------------------------------------------------
|
||
|
||
The reference design uses the :ref:`SPI Engine Framework <spi_engine>` to
|
||
interface with the AD4630 ADC. The design supports almost all possible digital
|
||
interface configurations of the device. In echo clock mode, because the clock
|
||
for data latching is routed back through the BUSY line, an additional data
|
||
capture module is used for saving the received samples and transmitting
|
||
forward for the DMA.
|
||
|
||
There are three modes in which the system can run. Refer to the :adi:`AD4630-24`,
|
||
:adi:`AD4630-16` or :adi:`AD4030-24` data sheet section titled SAMPLE CONVERSION
|
||
TIMING AND DATA TRANSFER for more explanation of data transfer zones.
|
||
|
||
Block diagram
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
The data path and clock domains are depicted in the below diagrams:
|
||
|
||
SPI mode - transfer zone 1
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
The main aspect of this mode is the fact that it is using the BUSY signal from
|
||
the ADC to trigger the Offload module. Data is then clocked out by the
|
||
Execution module and transferred to the DMA by the Offload module. CNV is
|
||
always generated by the AXI PWM GEN IP core regardless of the mode. Zone 1
|
||
transfer is not currently supported by the pre-compiled HDL files that are
|
||
included in the SD card image that is provided with the evaluation board.
|
||
|
||
.. image:: ad463x_hdl_cm0_cz1_1.svg
|
||
:width: 800
|
||
:align: center
|
||
:alt: AD4630_FMC SPI mode - transfer zone 1 block diagram
|
||
|
||
SPI mode - transfer zone 2
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
In this mode, the BUSY signal is not used and both the CNV and the Offload
|
||
trigger signals are generated by the AXI PWM GEN core. The reason for using two
|
||
PWM outputs instead of a common one is to accommodate for the averaging mode
|
||
where the two signals will have different frequencies.
|
||
|
||
.. image:: ad463x_hdl_cm0_cz2_1.svg
|
||
:width: 800
|
||
:align: center
|
||
:alt: AD4630_FMC SPI mode - transfer zone 2 block diagram
|
||
|
||
Echo clock mode - transfer zone 2
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
In this configuration, the ADC's BUSY-SCKOUT pin functions as a bit-clock
|
||
output and is generated by looping-through the host’s SCK. The SPI engine is
|
||
driving the SPI signals except it is no longer reading the data. For this
|
||
purpose, the Data Capture IP is used. This also allows for reading data in DDR
|
||
mode.
|
||
|
||
.. image:: ad463x_hdl_cm1_cz2_1.svg
|
||
:width: 800
|
||
:align: center
|
||
:alt: AD4630_FMC Echo clock mode - transfer zone 2 block diagram
|
||
|
||
The design supports the following interface and clock modes both in SDR and DDR:
|
||
|
||
================== ================== ================== ==================
|
||
Mode 1 Lane per channel 2 Lane per channel 4 lane per channel
|
||
================== ================== ================== ==================
|
||
SPI mode yes yes yes
|
||
Echo Clock mode yes yes yes
|
||
================== ================== ================== ==================
|
||
|
||
Configuration modes
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
The CLK_MODE configuration parameter defines clocking mode of the device's
|
||
digital interface: Options: 0 - SPI mode, 1 - Echo-clock or Master clock mode
|
||
|
||
The NUM_OF_SDI configutation parameter defines the number of MOSI lines of the
|
||
SPI interface: Options: 1 - Interleaved mode, 2 - 1 lane per channel,
|
||
4 - 2 lanes per channel, 8 - 4 lanes per channel
|
||
|
||
The CAPTURE_ZONE configuration parameter defines the capture zone of the next
|
||
sample. There are two capture zones: 1 - from negative edge of the BUSY line
|
||
until the next CNV positive edge -20ns, 2 - from the next consecutive CNV
|
||
positive edge +20ns until the second next consecutive CNV positive edge -20ns
|
||
|
||
The DDR_EN configuration parameter defines the type of data transfer. In echo
|
||
and master clock mode the SDI lines can have Single or Double Data Rates.
|
||
Options: 0 - MISO runs on SDR, 1 - MISO runs on DDR.
|
||
|
||
CPU/Memory interconnects addresses
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
The addresses are dependent on the architecture of the FPGA, having an offset
|
||
added to the base address from HDL(see more at :ref:`architecture`).
|
||
|
||
======================== ===========
|
||
Instance Address
|
||
======================== ===========
|
||
spi_ad463x_axi_regmap 0x44A0_0000
|
||
axi_ad463x_dma 0x44A3_0000
|
||
spi_clkgen 0x44A7_0000
|
||
cnv_generator 0x44B0_0000
|
||
======================== ===========
|
||
|
||
I2C connections
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
.. list-table::
|
||
:widths: 20 20 20 20 20
|
||
:header-rows: 1
|
||
|
||
* - I2C type
|
||
- I2C manager instance
|
||
- Alias
|
||
- Address
|
||
- I2C subordinate
|
||
* - PL
|
||
- iic_fmc
|
||
- axi_iic_fmc
|
||
- 0x4162_0000
|
||
- ---
|
||
* - PL
|
||
- iic_main
|
||
- axi_iic_main
|
||
- 0x4160_0000
|
||
- ---
|
||
|
||
SPI connections
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
.. list-table::
|
||
:widths: 25 25 25 25
|
||
:header-rows: 1
|
||
|
||
* - SPI type
|
||
- SPI manager instance
|
||
- SPI subordinate
|
||
- CS
|
||
* - PL
|
||
- axi_spi_engine
|
||
- ad4630
|
||
- 0
|
||
|
||
GPIOs
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
The Software GPIO number is calculated as follows:
|
||
|
||
- Zynq-7000: if PS7 is used, then offset is 54
|
||
|
||
.. list-table::
|
||
:widths: 25 25 25 25
|
||
:header-rows: 2
|
||
|
||
* - GPIO signal
|
||
- Direction
|
||
- HDL GPIO EMIO
|
||
- Software GPIO
|
||
* -
|
||
- (from FPGA view)
|
||
-
|
||
- Zynq-7000
|
||
* - ad463x_resetn
|
||
- INOUT
|
||
- 32
|
||
- 86
|
||
|
||
Interrupts
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
Below are the Programmable Logic interrupts used in this project.
|
||
|
||
=================== === ========== ===========
|
||
Instance name HDL Linux Zynq Actual Zynq
|
||
=================== === ========== ===========
|
||
axi_ad463x_dma 13 57 89
|
||
spi_ad463x 12 56 88
|
||
=================== === ========== ===========
|
||
|
||
Building the HDL project
|
||
-------------------------------------------------------------------------------
|
||
|
||
The design is built upon ADI's generic HDL reference design framework.
|
||
ADI does not distribute the bit/elf files of these projects so they
|
||
must be built from the sources available :git-hdl:`here </>`. To get
|
||
the source you must
|
||
`clone <https://git-scm.com/book/en/v2/Git-Basics-Getting-a-Git-Repository>`__
|
||
the HDL repository, and then build the project as follows:.
|
||
|
||
**Linux/Cygwin/WSL**
|
||
|
||
.. code-block::
|
||
:linenos:
|
||
|
||
user@analog:~$ cd hdl/projects/ad4630_fmc/zed
|
||
user@analog:~/hdl/projects/ad4630_fmc/zed$ make NUM_OF_SDI=4 CAPTURE_ZONE=2
|
||
|
||
The result of the build, if parameters were used, will be in a folder named
|
||
by the configuration used:
|
||
|
||
if the following command was run
|
||
|
||
``make NUM_OF_SDI=4 CAPTURE_ZONE=2``
|
||
|
||
then the folder name will be:
|
||
|
||
``NUMOFSDI4_CAPTUREZONE2``
|
||
|
||
A more comprehensive build guide can be found in the :ref:`build_hdl` user guide.
|
||
|
||
Resources
|
||
-------------------------------------------------------------------------------
|
||
|
||
Systems related
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
- :dokuwiki:`[Wiki] AD463X and AD403X Developer's Guide <resources/eval/ad4630-24-eval-board/ad4630-24-developer-guide>`
|
||
|
||
Hardware related
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
- Product datasheets:
|
||
|
||
- :adi:`AD4030-24`
|
||
- :adi:`AD4630-16`
|
||
- :adi:`AD4630-24`
|
||
- :dokuwiki:`[Wiki] AD4630/AD4030 Evaluation Board User Guide <resources/eval/ad4630-24-eval-board>`
|
||
|
||
HDL related
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
- :git-hdl:`AD4630_FMC HDL project source code <projects/ad4630_fmc>`
|
||
- :dokuwiki:`[Wiki] AD4630_FMC HDL project documentation <resources/eval/user-guides/ad463x/hdl>`
|
||
|
||
.. list-table::
|
||
:widths: 30 35 35
|
||
:header-rows: 1
|
||
|
||
* - IP name
|
||
- Source code link
|
||
- Documentation link
|
||
* - AD463X_DATA_CAPTURE
|
||
- :git-hdl:`library/ad463x_data_capture`
|
||
- ---
|
||
* - AXI_CLKGEN
|
||
- :git-hdl:`library/axi_clkgen`
|
||
- :dokuwiki:`[Wiki] <resources/fpga/docs/axi_clkgen>`
|
||
* - AXI_DMAC
|
||
- :git-hdl:`library/axi_dmac`
|
||
- :ref:`here <axi_dmac>`
|
||
* - AXI_HDMI_TX
|
||
- :git-hdl:`library/axi_hdmi_tx`
|
||
- :dokuwiki:`[Wiki] <resources/fpga/docs/axi_hdmi_tx>`
|
||
* - AXI_I2S_ADI
|
||
- :git-hdl:`library/axi_i2s_adi`
|
||
- ---
|
||
* - AXI_PWM_GEN
|
||
- :git-hdl:`library/axi_pwm_gen`
|
||
- :dokuwiki:`[Wiki] <resources/fpga/docs/axi_pwm_gen>`
|
||
* - AXI_SPDIF_TX
|
||
- :git-hdl:`library/axi_spdif_tx`
|
||
- ---
|
||
* - AXI_SPI_ENGINE
|
||
- :git-hdl:`library/spi_engine/axi_spi_engine`
|
||
- :ref:`here <spi_engine axi>`
|
||
* - SPI_AXIS_REORDER
|
||
- :git-hdl:`library/spi_engine/spi_axis_reorder`
|
||
- ---
|
||
* - SPI_ENGINE_EXECUTION
|
||
- :git-hdl:`library/spi_engine/spi_engine_execution`
|
||
- :ref:`here <spi_engine execution>`
|
||
* - SPI_ENGINE_INTERCONNECT
|
||
- :git-hdl:`library/spi_engine/spi_engine_interconnect`
|
||
- :ref:`here <spi_engine interconnect>`
|
||
* - SPI_ENGINE_OFFLOAD
|
||
- :git-hdl:`library/spi_engine/spi_engine_offload`
|
||
- :ref:`here <spi_engine offload>`
|
||
* - SYSID_ROM
|
||
- :git-hdl:`library/sysid_rom`
|
||
- :dokuwiki:`[Wiki] <resources/fpga/docs/axi_sysid>`
|
||
* - UTIL_I2C_MIXER
|
||
- :git-hdl:`library/util_i2c_mixer <library/util_i2c_mixer>`
|
||
- ---
|
||
|
||
- :ref:`SPI Engine Framework documentation <spi_engine>`
|
||
|
||
Software related
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
- :git-linux:`AD4630_FMC Linux driver source code <analogdevicesinc/linux/blob/main/drivers/iio/adc/ad4630.c>`
|
||
- :git-no-os:`AD463x_FMC No-OS project source code <projects/ad463x_fmcz>`
|
||
- :dokuwiki:`AD4630 ADC Linux Driver <resources/tools-software/linux-drivers/iio-adc/ad4630>`
|
||
- :dokuwiki:`AD463X ADC Linux Driver <resources/tools-software/linux-drivers/iio-adc/ad463x>`
|
||
- :dokuwiki:`AD4630/AD4030 - No-OS Driver <resources/tools-software/uc-drivers/ad463x>`
|
||
|
||
.. include:: ../common/more_information.rst
|
||
|
||
.. include:: ../common/support.rst
|