"assemble". And don't show "naked" (not occuring in anti-parallel
pairs) edges when just testing for interference.
[git-p4: depot-paths = "//depot/solvespace/": change = 1967]
separate polygon of coincident (with same or opposite normal)
faces; I instead test all the edges against the other shell, and
have extended the classify-against-shell stuff to handle those
cases.
And the normals are now perturbed a bit numerically, to either side
of the edge, to distinguish tangency from a coincident surface.
This seems to work fairly well, although things still tend to fail
when the piecewise linear tolerance is too coarse.
[git-p4: depot-paths = "//depot/solvespace/": change = 1964]
can show edges for both meshes and shells, and export them and
hidden line remove and all the usual stuff.
And fix the zoom to fit on startup, so that it considers hidden
entities too. That avoids the problem where things get generated at
stupid chord tolerance because no entities were visible and the
mesh of course did not yet exist.
[git-p4: depot-paths = "//depot/solvespace/": change = 1961]
exact surface shells. And add interference checking; I'll be lazy
and just do that on the meshes, by modifying the self-intersection
tester to ignore coplanar triangles (since that can happen in an
assembly).
[git-p4: depot-paths = "//depot/solvespace/": change = 1958]
a mesh than that's a copy, and if we're working with a shell then
it's the shell's triangulation.
[git-p4: depot-paths = "//depot/solvespace/": change = 1957]
a grid of quads, with adaptive spacing. The quads that lie entirely
within the trim polygon are triangulated and knocked out from the
polygon, and then the polygon is triangulated.
That works okay, though rather slow. But there are issues with
surfaces of revolution that touch the axis, since they end up with
a singularity. That will require some thought.
[git-p4: depot-paths = "//depot/solvespace/": change = 1951]
tables from SolveSpace to their own class. This is intended to
simplify use of the constraint solver in a library.
[git-p4: depot-paths = "//depot/solvespace/": change = 1942]
our specified section plane; we then split them according to the
start and endpoints of each STrimBy, using de Castejau's algorithm.
These sections get projected (possibly in perspective, which I do
correctly) into 2d and exported.
Except, for now they just get pwl'd in the export files. That's the
fallback, since it works for any file format. But that's the place
to add special cases for circles etc., or to export them exactly.
DXF supports the latter, but very painfully since I would need to
write a later-versioned file, which requires thousands of lines of
baggage. I'll probably stick with arcs.
[git-p4: depot-paths = "//depot/solvespace/": change = 1936]
and curve.cpp and surface.cpp contain the rest.
Also get rid of the meshError stuff; will just use the nakedEdges
mechanism for that. And I won't run the interference test
continuously, have added a menu item for that.
[git-p4: depot-paths = "//depot/solvespace/": change = 1934]
triangle join. And add controls to show and hide the solid model
edges (independently of the shaded mesh), and to suppress the
shaded triangles from SVG/EPS output.
[git-p4: depot-paths = "//depot/solvespace/": change = 1932]
export. So I calculate lighting for each triangle in the mesh, make
a BSP, and then traverse it in-order and output those as SVG or
EPS. And I test edges against the mesh, removing those portions of
the edge that overlap a triangle in front of them (using the
kd-tree to accelerate).
[git-p4: depot-paths = "//depot/solvespace/": change = 1931]
use that for surface-line intersections. That has major problems
with the heuristic on when to stop and do Newton polishing.
There's also an issue with all the Newton stuff when surfaces join
tangent.
And update the wishlist to reflect current needs.
[git-p4: depot-paths = "//depot/solvespace/": change = 1925]
fix convergence tolerance so that points projected into a rational
polynomial surface end up much closer than LENGTH_EPS.
[git-p4: depot-paths = "//depot/solvespace/": change = 1906]
the same precedence as sqrt. Add the code to find naked edges, and
draw them highlighted on the model. And make the direction of trim
curves consistent, always ccw with normal toward viewer; so there's
no need to fix the directions before triangulating.
[git-p4: depot-paths = "//depot/solvespace/": change = 1903]
from an extrusion, with piecewise linear trim curves for everything
(that are shared, so that they appear only once for the two
surfaces that each trims). No Boolean operations on them, and the
triangulation is bad, because gl seems to merge collinear edges.
So before going further, I seem to need my own triangulation code.
I have not had great luck in the past, but I can't live without it
now.
[git-p4: depot-paths = "//depot/solvespace/": change = 1899]
corresponding to each param from the Jacobian, and see if it loses
rank. If it does then that one was important, so it's bound. Then
display a big blue square around its point until the next normal
solve.
[git-p4: depot-paths = "//depot/solvespace/": change = 1887]
tables in the code, which I have written in perl and am checking
in.
Also get WM_MOUSELEAVE events from win32, so that I can de-hover
everything when the mouse leaves the graphics window. And fix one
of the icons, which was 23x24 instead of 24x24.
[git-p4: depot-paths = "//depot/solvespace/": change = 1883]
auto-showing when a solve fails. And accept expressions, not just
numbers, for that new dimension value.
[git-p4: depot-paths = "//depot/solvespace/": change = 1877]
just applies an offset to the DXF before exporting. Useful enough
to be worth the ugliness, though.
This is the stupid routines from SketchFlat, slightly reworked.
[git-p4: depot-paths = "//depot/solvespace/": change = 1866]
linear segments to generate, irrespective of the chord tolerance.
That used to be hard-coded, and it needs to be small enough to
avoid lags while working interactively, but I also need to export
fine geometry.
[git-p4: depot-paths = "//depot/solvespace/": change = 1857]
lets us export open curves, if the user drew them that way.
Also increase the limits on how many pwls we will generate for a
single curve.
[git-p4: depot-paths = "//depot/solvespace/": change = 1854]
some magic numbers. This would be trivial to break, but still more
difficult than patching the binary to skip the check...
[git-p4: depot-paths = "//depot/solvespace/": change = 1853]
theorem; it's evaluated as a surface integral over each triangle.
And don't regenerate the emphasized edges unless we have to;
specifically, don't do it when the only dirty group is the
drawing group.
[git-p4: depot-paths = "//depot/solvespace/": change = 1849]
And fix a bug; wasn't asking the user whether to save before
abandoning file when a new file was opened recent.
[git-p4: depot-paths = "//depot/solvespace/": change = 1830]
based on a chord tolerance. And rewrite the pwl circles to work
against a chord tolerance too (which they really were doing before,
but in funny units).
Also make "assemble" combine type do a union after interference
checking; was previously just copying, which meant that coplanar
faces could break subsequent operations.
And make right-clicking effectively toggle shift key, instead of
forcing it on; so you can pan or rotate with either right or middle
button.
[git-p4: depot-paths = "//depot/solvespace/": change = 1829]
where it was, move the export (DXF, PNG, STL) stuff to export.cpp,
and move the regen/solve stuff to generate.cpp.
[git-p4: depot-paths = "//depot/solvespace/": change = 1825]
all coordinates are divided by that number as we export.
And add functions to store a float in the registry. I'm using those
for the scale factor, and also to replace the crazy scaled integers
that I was using for light positions etc. before.
[git-p4: depot-paths = "//depot/solvespace/": change = 1824]
specify the plane from which we want to grab the triangles. Shared
edges are then removed with the same code used to check for
watertight meshes, and the remaining edges are assembled into
polygons.
[git-p4: depot-paths = "//depot/solvespace/": change = 1823]
introduced by the bsp routines. It's usually, though not always,
possible to generate a watertight mesh. The occasions where it's
not look ugly, floating point issues, no quick fix.
And use those to generate a list of edges where two different faces
meet, which I can emphasize for cosmetic reasons (and some UI to
specify whether to do that, and with what color).
And make the right mouse button rotate the model, since that was
previously doing nothing.
[git-p4: depot-paths = "//depot/solvespace/": change = 1821]
that to try to find them if we can't find them by absolute path.
This is intended to make everything still work if you copy an
entire directory tree of files that import each other.
Also add a mechanism to not paint the scene if we're not sure it's
consistent; otherwise got some crashes on startup. And disable both
text and graphic window when displaying a modal dialog, wasn't
doing that always.
[git-p4: depot-paths = "//depot/solvespace/": change = 1808]
separate groups. The section is swept normal to the trajectory,
producing a mesh. I'm doing the triangles only now, not copying
over any entities.
Also fix a bug in the PNG export; rows are 4-aligned, so that was
breaking when the width of the image wasn't divisible by four. Also
fix a bug in lathes, where it generated overlapping triangles for
one segment.
And change the groups to record both "this mesh", the contribution
due to the extrude/lathe/whatever, and the "running mesh", that we
get after applying the requested Boolean op between "this mesh" and
the previous group's "running mesh". I'll use that to make step and
repeats step the mesh too.
[git-p4: depot-paths = "//depot/solvespace/": change = 1801]
that perspective in the gl matrices, and also everywhere that I
check mouse pointer positions against the model, and for the zoom
to fit.
[git-p4: depot-paths = "//depot/solvespace/": change = 1796]
user-visible text. And make points hoverable/selectable even when
GW.showPoints is false, and zoom to fit before regenerating on file
open, because then we're at the right zoom level (and will use the
right pwl tolerance).
[git-p4: depot-paths = "//depot/solvespace/": change = 1788]
to save our registry stuff (because we were calling exit() instead
of doing a PostQuitMessage()), and a misclassification of triangles
coplanar with the test surface, when the test surface contained
zero-area triangles.
[git-p4: depot-paths = "//depot/solvespace/": change = 1773]
Jonathan Westhues