99 lines
2.9 KiB
Verilog
99 lines
2.9 KiB
Verilog
/*
|
||
Copyright 2020 Blue Liang, liangkangnan@163.com
|
||
|
||
Licensed under the Apache License, Version 2.0 (the "License");
|
||
you may not use this file except in compliance with the License.
|
||
You may obtain a copy of the License at
|
||
|
||
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
||
Unless required by applicable law or agreed to in writing, software
|
||
distributed under the License is distributed on an "AS IS" BASIS,
|
||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
See the License for the specific language governing permissions and
|
||
limitations under the License.
|
||
*/
|
||
|
||
|
||
// GPIO模块
|
||
module gpio(
|
||
|
||
input wire clk,
|
||
input wire rst,
|
||
|
||
input wire we_i,
|
||
input wire[31:0] addr_i,
|
||
input wire[31:0] data_i,
|
||
|
||
output reg[31:0] data_o,
|
||
|
||
input wire[1:0] io_pin_i,
|
||
output wire[31:0] reg_ctrl,
|
||
output wire[31:0] reg_data
|
||
|
||
);
|
||
|
||
|
||
// GPIO控制寄存器
|
||
localparam GPIO_CTRL = 4'h0;
|
||
// GPIO数据寄存器
|
||
localparam GPIO_DATA = 4'h4;
|
||
|
||
// 每2位控制1个IO的模式，最多支持16个IO
|
||
// 0: 高阻，1：输出，2：输入
|
||
reg[31:0] gpio_ctrl;
|
||
// 输入输出数据
|
||
reg[31:0] gpio_data;
|
||
|
||
|
||
assign reg_ctrl = gpio_ctrl;
|
||
assign reg_data = gpio_data;
|
||
|
||
|
||
// 写寄存器
|
||
always @ (posedge clk) begin
|
||
if (rst == 1'b0) begin
|
||
gpio_data <= 32'h0;
|
||
gpio_ctrl <= 32'h0;
|
||
end else begin
|
||
if (we_i == 1'b1) begin
|
||
case (addr_i[3:0])
|
||
GPIO_CTRL: begin
|
||
gpio_ctrl <= data_i;
|
||
end
|
||
GPIO_DATA: begin
|
||
gpio_data <= data_i;
|
||
end
|
||
endcase
|
||
end else begin
|
||
if (gpio_ctrl[1:0] == 2'b10) begin
|
||
gpio_data[0] <= io_pin_i[0];
|
||
end
|
||
if (gpio_ctrl[3:2] == 2'b10) begin
|
||
gpio_data[1] <= io_pin_i[1];
|
||
end
|
||
end
|
||
end
|
||
end
|
||
|
||
// 读寄存器
|
||
always @ (*) begin
|
||
if (rst == 1'b0) begin
|
||
data_o = 32'h0;
|
||
end else begin
|
||
case (addr_i[3:0])
|
||
GPIO_CTRL: begin
|
||
data_o = gpio_ctrl;
|
||
end
|
||
GPIO_DATA: begin
|
||
data_o = gpio_data;
|
||
end
|
||
default: begin
|
||
data_o = 32'h0;
|
||
end
|
||
endcase
|
||
end
|
||
end
|
||
|
||
endmodule
|