137 lines
4.1 KiB
Systemverilog
137 lines
4.1 KiB
Systemverilog
/*
|
||
Copyright 2020 Blue Liang, liangkangnan@163.com
|
||
|
||
Licensed under the Apache License, Version 2.0 (the "License");
|
||
you may not use this file except in compliance with the License.
|
||
You may obtain a copy of the License at
|
||
|
||
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
||
Unless required by applicable law or agreed to in writing, software
|
||
distributed under the License is distributed on an "AS IS" BASIS,
|
||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
See the License for the specific language governing permissions and
|
||
limitations under the License.
|
||
*/
|
||
|
||
// GPIO模块
|
||
module gpio(
|
||
|
||
input wire clk,
|
||
input wire rst_n,
|
||
input wire[31:0] addr_i,
|
||
input wire[31:0] data_i,
|
||
input wire[3:0] sel_i,
|
||
input wire we_i,
|
||
output wire[31:0] data_o,
|
||
|
||
input wire req_valid_i,
|
||
output wire req_ready_o,
|
||
output wire rsp_valid_o,
|
||
input wire rsp_ready_i,
|
||
|
||
input wire[1:0] io_pin_i,
|
||
output wire[31:0] reg_ctrl,
|
||
output wire[31:0] reg_data
|
||
|
||
);
|
||
|
||
// GPIO寄存器(偏移)地址
|
||
localparam GPIO_CTRL = 4'h0;
|
||
localparam GPIO_DATA = 4'h4;
|
||
|
||
// GPIO控制寄存器
|
||
// 每2位控制1个IO的输入、输出模式，最多支持16个IO
|
||
// 0: 高阻，1：输出，2：输入
|
||
reg[31:0] gpio_ctrl;
|
||
|
||
// GPIO输入输出数据寄存器
|
||
reg[31:0] gpio_data;
|
||
|
||
assign reg_ctrl = gpio_ctrl;
|
||
assign reg_data = gpio_data;
|
||
|
||
wire wen = we_i & req_valid_i;
|
||
wire ren = (~we_i) & req_valid_i;
|
||
wire write_reg_ctrl_en = wen & (addr_i[3:0] == GPIO_CTRL);
|
||
wire write_reg_data_en = wen & (addr_i[3:0] == GPIO_DATA);
|
||
|
||
// 写gpio_ctrl
|
||
always @ (posedge clk or negedge rst_n) begin
|
||
if (!rst_n) begin
|
||
gpio_ctrl <= 32'h0;
|
||
end else begin
|
||
if (write_reg_ctrl_en) begin
|
||
if (sel_i[0]) begin
|
||
gpio_ctrl[7:0] <= data_i[7:0];
|
||
end
|
||
if (sel_i[1]) begin
|
||
gpio_ctrl[15:8] <= data_i[15:8];
|
||
end
|
||
if (sel_i[2]) begin
|
||
gpio_ctrl[23:16] <= data_i[23:16];
|
||
end
|
||
if (sel_i[3]) begin
|
||
gpio_ctrl[31:24] <= data_i[31:24];
|
||
end
|
||
end
|
||
end
|
||
end
|
||
|
||
// 写gpio_data
|
||
always @ (posedge clk or negedge rst_n) begin
|
||
if (!rst_n) begin
|
||
gpio_data <= 32'h0;
|
||
end else begin
|
||
if (write_reg_data_en) begin
|
||
if (sel_i[0]) begin
|
||
gpio_data[7:0] <= data_i[7:0];
|
||
end
|
||
if (sel_i[1]) begin
|
||
gpio_data[15:8] <= data_i[15:8];
|
||
end
|
||
end else begin
|
||
if (gpio_ctrl[1:0] == 2'b10) begin
|
||
gpio_data[0] <= io_pin_i[0];
|
||
end
|
||
if (gpio_ctrl[3:2] == 2'b10) begin
|
||
gpio_data[1] <= io_pin_i[1];
|
||
end
|
||
end
|
||
end
|
||
end
|
||
|
||
reg[31:0] data_r;
|
||
|
||
// 读寄存器
|
||
always @ (posedge clk or negedge rst_n) begin
|
||
if (!rst_n) begin
|
||
data_r <= 32'h0;
|
||
end else begin
|
||
if (ren) begin
|
||
case (addr_i[3:0])
|
||
GPIO_CTRL: data_r <= gpio_ctrl;
|
||
GPIO_DATA: data_r <= gpio_data;
|
||
default: data_r <= 32'h0;
|
||
endcase
|
||
end else begin
|
||
data_r <= 32'h0;
|
||
end
|
||
end
|
||
end
|
||
|
||
assign data_o = data_r;
|
||
|
||
vld_rdy #(
|
||
.CUT_READY(0)
|
||
) u_vld_rdy(
|
||
.clk(clk),
|
||
.rst_n(rst_n),
|
||
.vld_i(req_valid_i),
|
||
.rdy_o(req_ready_o),
|
||
.rdy_i(rsp_ready_i),
|
||
.vld_o(rsp_valid_o)
|
||
);
|
||
|
||
endmodule
|